BYD home charger: wallbox installation for family homes
Any Type 2 wall charger works with a BYD, but how it is connected matters: the 44.9 kWh Dolphin charges on a single phase only, at up to 7.4 kW, while the other BYD models charge on three phases at 11 kW. As an independent electrician we choose and set up the charger for the car and the house supply, build the circuit and, if needed, handle the capacity increase with the utility. We are not an official BYD partner; we hand over the installation with protection tests and a test report.
How fast does each BYD charge at home?
Most BYDs charge on AC at 11 kW on three phases (3×16 A); the exception is the 44.9 kWh Dolphin, which charges on a single phase only, at up to 7.4 kW (1×32 A).
| Model (version) | Max. AC charging | Phases × current | Usable battery | 0–100 % at max. AC |
|---|---|---|---|---|
| Dolphin 44.9 kWh (Active/Boost) | 7.4 kW | 1×32 A only | 44.9 kWh | approx. 7 h 15 min |
| Dolphin 60.4 kWh (model year 2025) | 11 kW | 3×16 A | 60.5 kWh | approx. 6 h 30 min |
| Atto 2 45.12 kWh | 11 kW | 3×16 A | 45.1 kWh | approx. 5 h |
| Atto 3 | 11 kW | 3×16 A | 60.5 kWh | approx. 6 h 30 min |
| Seal 82.5 kWh RWD | 11 kW | 3×16 A | 82.5 kWh | approx. 9 h |
| Seal U 87 kWh (battery electric) | 11 kW | 3×16 A | 87.0 kWh | approx. 9 h 30 min |
Source: ev-database.org. None of these models accepts 22 kW on AC, so a 22 kW connection does not speed up a BYD.
Why is a BYD Dolphin slow on a three-phase wallbox?
Because the 44.9 kWh Dolphin uses only one phase, so a three-phase wallbox set to 3×16 A gives it a single 16 A phase, which is about 3.7 kW: half of the possible 7.4 kW, so charging takes about twice as long.
For the full 7.4 kW the charger must be able to deliver 32 A on one phase, and the house must be able to supply it: the meter needs a main fuse of at least 32 A on that phase, which on a 3×16 A connection means a capacity increase. There are two good solutions:
- A single-phase 32 A connection, or a charger that can be set to 32 A on one phase — if only the Dolphin charges at the house.
- A three-phase charger that can also deliver 32 A on one phase — if a three-phase 11 kW car (for example an Atto 3 or a Tesla) charges there too, now or later.
The 60.4 kWh Dolphin, the Atto 2, the Atto 3, the Seal and the Seal U charge on three phases, so the usual 3×16 A, 11 kW connection is right for them. Before buying, check which Dolphin will be parked in the garage; we ask about this during the survey.
Which charging connector does a BYD have?
BYDs sold in Europe use Type 2 for AC charging and CCS2 for DC fast charging. A home wall charger is AC, so it has a Type 2 connector; CCS2 is for public fast chargers, not for home.
This means you do not need a “BYD” charger at home: any Type 2 wallbox charges it, including the Tesla Wall Connector if access is enabled for all vehicles in the Tesla One app. More on that on our Tesla home charger page.
Do I need a separate BYD charging cable or a factory charger?
At home you do not need a separate cable if the wall charger is tethered: you simply plug its Type 2 connector into the car. A socket-type (untethered) wallbox and public AC charging points need a Type 2 to Type 2 cable.
Which cable or portable charger comes with a given model is stated in the dealer’s equipment list. The wall charger does not have to be BYD-branded: the charging speed is limited by the car’s on-board charger (7.4 or 11 kW), not by the brand of the charger.
Which wall charger should I choose for a BYD?
A Type 2 wallbox that matches the car’s number of phases: an 11 kW (3×16 A) charger for a three-phase BYD, and a charger that can deliver 32 A on one phase for the 44.9 kWh Dolphin. Through our wholesale partner Mile Kft. we can source and install several brands:
| Brand | Model | Note |
|---|---|---|
| Schneider Electric | EVlink Home, EVlink Charge Pro | home and “pro” versions |
| ABB | Terra AC (W4–W22) | the model code indicates the power |
| Besen | Wallbox Smart 11/22 kW | one of the most searched brands in Hungary |
| Fronius | Wattpilot Home 11/22 kW | for solar PV systems |
| Tesla | Wall Connector Gen 3 | charges other brands too if enabled |
| Other brands | OBO, Eaton, Sigenergy | on request |
Before recommending a model for the Dolphin, we check in the manufacturer’s data sheet that it can be set to 32 A on one phase.
What does the house need for a BYD wall charger?
| Element | Why it is needed | What we check |
|---|---|---|
| Supply and phases | a three-phase BYD needs 3×16 A, the 44.9 kWh Dolphin needs 32 A on one phase | number of phases and main fuse at the meter |
| Capacity | the charger draws close to full current for hours alongside the other loads | if it is not enough, we request an increase from the distribution operator (E.ON, MVM or Opus Titász) |
| Dedicated circuit and cable | the charger cannot share its circuit | its own breaker; the cross-section depends on the current and the length of the run |
| Residual current device (RCD) | the car can cause DC fault currents that a standard type A RCD does not detect | type A-EV or B, depending on the charger’s built-in DC detection |
| Load management | the oven or the heat pump may run while the car charges | we set the charger’s current limit to the house |
| Solar charging | daytime surplus goes into the car instead of the grid | a wallbox or control that follows the current PV output |
| Cable route and location | garage, carport or fence; it has to work in rain and frost | IP rating, cable routing, buried cable if needed |
Rules and cost factors are described on our EV charger installation page; if the meter cabinet or the distribution board also needs replacing, see electrical installation. In a new house we plan the charger cable and the board space during electrical design.
How much does BYD charger installation cost, and is there a grant?
The installation price depends on the cable run, the condition of the distribution board and whether a capacity increase is needed, so we quote after a site survey or from photos of the meter cabinet and the distribution board. The quotation lists the charger, the installation and the paperwork on separate lines. You can send photos via the details on our contact page.
There is no state grant for private home chargers in October 2026, and there has never been a dedicated programme: the E-AUTO-2021 residential scheme only supported buying the car.
How does a BYD charger installation work?
- 1Survey or photos
We ask which BYD model and battery version will charge, and check the meter (phases, main fuse), the distribution board and the cable route. In simpler cases, photos of the meter cabinet and the board are enough for a first quotation.
- 2Quotation and choice of charger
A charger matching the car’s phases, cable, protection, board extension and paperwork on separate lines.
- 3Paperwork
If needed, notification or capacity increase with the distribution operator; the installation date then follows the utility’s procedure, which takes several weeks, sometimes a few months.
- 4Installation
Dedicated circuit from the main board, sized cable, circuit breaker and a suitable RCD, mounting the charger. The installation itself is usually short.
- 5Commissioning and handover
Setting the charger’s current limit and phase configuration for the car and the house, protection tests and test report, and a walk-through.
Frequently asked questions
Do you install a charger for a BYD bought from wallbox.hu or another web shop?
Yes. We install Type 2 wall chargers bought from wallbox.hu or any other web shop for a BYD too: we build the circuit, mount and commission the charger, and hand over the electrical safety test report. It is worth checking with us before you buy: the Dolphin 44.9 kWh charges on a single phase only, so the charger must be set to 1×32 A.
Which charger does the BYD Dolphin need?
The 44.9 kWh Dolphin charges on a single phase only, at up to 7.4 kW (1×32 A), so it needs a charger that can deliver 32 A on one phase, and the house has to supply it. The 60.4 kWh Dolphin charges on three phases at 11 kW, so the usual 3×16 A wallbox is right for it.
Which connector does a BYD have?
Type 2 for AC charging and CCS2 for DC fast charging. A home wall charger has a Type 2 connector.
Do I need a BYD factory charger for home charging?
No. Any Type 2 wall charger charges a BYD; the speed is set by the car’s on-board charger, not by the brand of the charger.
Can I charge a BYD from a normal socket?
Occasionally, with a portable charging cable, yes, but it is slow (about 2.3 kW), and a standard socket and circuit are not made for hours of near-full load. For regular charging we recommend a wall charger on a dedicated circuit.
Do I need a 22 kW charger for a BYD?
No. Current BYD models charge on AC at 11 kW at most (the 44.9 kWh Dolphin at 7.4 kW), so a 22 kW connection is not faster, only more expensive.
Are you an official BYD partner?
No. As an independent electrician we install wall chargers for electric cars of any brand to the electrical standards, with protection tests and a test report.
Is there a grant for home chargers?
In October 2026 there is no open state grant for private home chargers; the E-AUTO-2021 residential scheme also only supported buying the car.
Let’s talk about your project.
Tell us what you are planning and we will get back to you within a few days.
Get in touch