Smart home: KNX or a wireless system?
For a new house or a full renovation we recommend wired KNX; for an existing, lived-in house a wireless system. The deciding factor is not the price but whether the walls are already plastered: whether the wall chases for the electrical conduits are still accessible.
In short
- For a new house or a full renovation we recommend wired KNX: typically HUF 5–8 million for a 120–150 m² house, expandable for decades and manufacturer-independent.
- For an existing, lived-in house or a smaller budget a wireless system fits (Zigbee, Z-Wave, Wi-Fi modules, Matter): roughly HUF 0.6–2.3 million for the same house, installed without opening walls.
- The deciding factor is not the price but whether the walls are already plastered: whether the wall chases for the electrical conduits are still accessible.
Author: Norbert Madarász
, Managing Director and Partner · Updated: 14 November 2026
Three questions that decide
- Are the walls still unplastered? While the wall chases are open, the conduit for the bus cable goes next to the other electrical conduits – only a little extra work. Later the same means chiselling, filling, sanding and painting.
- How long will the family stay in the house? If you plan for 20–30 years, manufacturer independence and repairability are worth more than the initial saving.
- How independent should it be from the cloud and Wi-Fi? KNX works without the internet. Some wireless systems depend on a vendor cloud or the home Wi-Fi.
Comparison
| Criterion | Wired KNX | Wireless (Zigbee, Z-Wave, Wi-Fi, Matter) |
|---|---|---|
| When it can be installed | new build, full renovation, while the walls are unplastered | any time, also in a lived-in house |
| Cost for a 120–150 m² house (indicative) | HUF 5–8 million | HUF 0.6–2.3 million |
| Cabling | green bus cable (29 V) to every switch and sensor | no extra cable; modules go into the existing boxes |
| Manufacturers | more than 500 manufacturers, one standard (EN 50090, ISO/IEC 14543-3) | varies by vendor; Matter moves towards a common standard |
| Works without internet | yes, the bus runs on its own | partly: many devices need a vendor cloud or Wi-Fi |
| Battery replacement | none, the bus powers the devices | typically every 1–3 years in battery sensors |
| Expandability | any time, with devices from any manufacturer | within the chosen ecosystem |
| Troubleshooting | specialist, ETS programming | often the owner can do it |
How much does a KNX system cost?
In our experience the KNX system of a 120–150 m² family house typically costs HUF 5–8 million: hardware about 45–55%, design 10–15%, installation 20–25%, programming and commissioning 10–15%.
| Package (120–150 m²) | Scope | Indicative price |
|---|---|---|
| Basic | lighting and shading | HUF 3–4 million |
| Medium | basic + heating/cooling and access control | HUF 5–6 million |
| Full | medium + energy metering and visualisation | HUF 7–8 million |
The price depends mainly on the number of controlled circuits, the number of dimmed circuits and blinds, and on the visualisation.
What is a wireless system good for?
- In a lived-in house, without opening walls: a relay or dimmer module goes behind the switch into the existing box, and the light can be switched from the phone.
- To start with: a few rooms, a few functions, expandable later.
- As an addition to KNX: where no cable can be run later (e.g. garden gate, outbuilding), a radio device is used and works in one system through a gateway.
What to watch out for
- Neutral conductor: many flush-mounted modules only work if there is a neutral in the switch box. Older houses often have none; we check this during the survey.
- Load rating and heat: there is little space in the box behind the switch, and the module warms up. Choose the module for the real load, with a margin.
- Coverage: thick walls and slabs weaken the radio link; the mesh of Zigbee and Thread helps, while Wi-Fi devices depend on the router’s coverage.
- Compliant installation: a 230 V module is electrical work; it should be installed by an electrician according to the applicable standards.
Manufacturer systems: FIBARO and Grenton
A wireless smart home does not have to be built from individual modules: there are complete systems from a single manufacturer. Two common examples, based on the manufacturers’ own descriptions:
- FIBARO: a wireless, Z-Wave-based system. Its hub is the Home Center 3, which according to the manufacturer’s manual also handles Wi-Fi, Zigbee and Nice devices besides Z-Wave, and works with Z-Wave Plus certified devices from other manufacturers. Scenes are built with a block editor or Lua scripts. FIBARO was founded in Poznań in 2010 and has belonged to the Italian Nice group since 2018.
- Grenton: a hybrid system from Grenton Sp. z o.o. of Kraków. In a new house the modules connect to the central unit (CLU) over a wired bus (TF-Bus) and Ethernet; in existing buildings, according to the manufacturer, it can also be installed with Wi-Fi and Z-Wave modules, without opening walls. The configuration software (Object Manager) can be used without extra fees or licences, according to the manufacturer.
Both are single-manufacturer systems: the central unit and the programming tie you to the manufacturer. In KNX, by contrast, devices from hundreds of manufacturers are interchangeable. A detailed comparison of the wired systems (KNX, Loxone, Grenton): Loxone or KNX?
A mixed solution: KNX preparation
If the walls are still unplastered but a full KNX system does not fit the budget yet, KNX preparation is the best decision: the conduit for the bus cable goes into the wall chases, we pull the bus cable and build the distribution board. The expensive part – devices and programming – can follow later, even in stages. Afterwards the cable is the most expensive item; beforehand it is the cheapest.
More: KNX smart home · Electrical installation · Low-voltage systems
Frequently asked questions
Can KNX be retrofitted?
In an existing house wired KNX is only realistic together with a renovation, because it needs the bus cable. Partial solutions are KNX RF (radio) devices and modules that fit existing switch positions.
Which is better: KNX or Loxone?
Both are wired systems. KNX is an open standard with more than 500 manufacturers; Loxone is one manufacturer’s closed system with a central controller. We recommend KNX because devices are interchangeable and any KNX partner can take the system over.
How much does a smart home system cost?
For a 120–150 m² house typically HUF 5–8 million with wired KNX and HUF 0.6–2.3 million with a wireless system, depending on the number of functions. This is an indicative range; the final price follows a site survey and an itemised quote.
Does a smart home work without internet?
KNX does: switches, sensors and automations work without the internet; only remote access and the app need it. With wireless systems it depends on the vendor; prefer local control (e.g. Matter, a local Zigbee hub).
Are FIBARO and Grenton wireless systems?
FIBARO is: a Z-Wave-based radio system with the Home Center 3 hub. Grenton is hybrid: in a new house it runs on a wired bus (TF-Bus); in existing buildings it can also be installed with Wi-Fi and Z-Wave modules without opening walls, according to the manufacturer. Both are single-manufacturer systems, while KNX is an open standard.
Does KNX need a phone app?
No: the house works from the wall switches and automations. Visualisation (tablet, phone) is an optional extra.
Let’s talk about your project.
Tell us what you are planning and we will get back to you within a few days.
Get in touch