KNOWLEDGE BASE · SMART HOME

Smart blinds and shading: weather station, wind alarm, and what happens in a power cut?

Smart blinds are more than remote-controlled: they move by schedule, sun position and weather, and protect themselves from the wind. The heart of KNX shading control is the weather station, which measures wind, precipitation, brightness and temperature; at the set limits the blind actuator moves external venetian blinds or awnings into a safe position. Yet the most important question is rarely asked: what happens in a power cut, and what if the sensor itself fails?

In short

  • Smart blinds: motorised roller shutters, external venetian blinds or awnings controlled by an actuator; operated from a wall button, an app and automatically.
  • Weather station: measures wind, precipitation, brightness from several directions and temperature; more advanced models take time and location from GPS and calculate the sun position.
  • Wind alarm: the threshold must come from the blind manufacturer’s wind resistance data, not a guess. The system also goes to the safe position if the sensor signal stops arriving.
  • Power cut: 230 V motors stop where they are. Nothing retracts a lowered blind, so the wind alarm and away settings must be planned for this too.

Author: Norbert Madarász, Managing Director and Partner · Updated: 10 November 2026

What makes blinds smart?

Every motorised shading product has three parts: the motor (a tubular motor in a roller shutter, a gear motor in an external venetian blind), the control (a KNX blind actuator in the distribution board, or a radio receiver in the motor) and the operation (wall button, app, automation). It becomes “smart” when the control reacts not just to a button but to time, sun position, weather and the rest of the house.

ShadingGood forSensitive to
Roller shutterblackout, burglary protection, insulation in winterfrost: moving frozen slats can cause damage
External venetian blindsummer heat protection and light control via slat anglewind: lowered slatted blinds are the most sensitive
Awning, screenshading terraces and large glazingwind and rain: manufacturers usually require retraction

With radio motors, blinds in an existing house can be made smart too. In a new house or full renovation, however, a wired solution (motor cable to the board, KNX bus cable to the buttons) is more reliable, and shading runs in one system with lighting and heating. See: KNX or wireless smart home?

Blind motors: Somfy io, RTS or wired?

Searches for “blind motor” and “Somfy” usually come down to the same question: which motor goes into the blind, and what controls it. Somfy offers three options, and we install all three.

MotorHow it receives commandsFeedbackBest for
Somfy io (io-homecontrol)by radio, two-wayyes: command confirmation and blind positionexisting houses, smart home app, TaHoma hub
Somfy RTSby radio, one-waynonesimple remote control, extending an existing RTS system
Wired motor (230 V, up/down)the motor cable runs to the distribution board, where a blind actuator controls itthe KNX blind actuator calculates the position from travel timenew builds and full renovations, KNX or Loxone
  • According to Somfy, the main visible difference between io and RTS is the feedback. The TaHoma Switch hub controls both, but receives status only from io devices.
  • Whether a remote is io or RTS can be seen from its name (for example Situo io or Situo RTS).
  • In a new house we recommend wired motors: the blind actuator sits in the board, and wind alarms and sun tracking (below) work reliably without radio. In an existing house with no cable to the blind box, a wireless io motor is the right choice.

What does a KNX weather station measure?

  • Wind: wind speed (more advanced models also direction). This drives the wind alarm.
  • Precipitation: with a heated sensor surface, so mist and dew do not trigger false alarms, and the signal ends soon after the rain stops.
  • Brightness: with separate sensors in several directions, per facade. The automation uses this to decide which side needs shading.
  • Twilight and temperature: lowering in the evening, recognising frost risk.
  • GPS, sun position: more advanced stations take time and location from the GPS signal and calculate the sun’s position (azimuth and elevation).

Where the station goes matters as much as which one it is. According to the manufacturer’s instructions, it must be mounted where wind, rain and sun reach it unobstructed, not shaded by building parts or trees, with no structure above from which water can keep dripping after the rain, and with at least 60 cm of clearance around it.

Sun tracking: how external blinds keep out summer heat

External venetian blinds work best when the slat angle follows the sun’s elevation: closed just enough to keep direct sunlight out while letting diffuse light in (slat tracking). Shadow edge tracking goes further: the blind only lowers as far as needed for the sun patch on the floor to stay within a set depth.

For this the automation needs to know which facade gets sun when (sun position, brightness per direction) and the state of the room (indoor temperature, presence, heating or cooling mode). In the heating season sunlight is free heat, so the automation lets it in. In a passive house this is the key to summer heat protection: KNX smart home.

Wind, rain and frost alarms: how does the protection work?

  1. The limit comes from the manufacturer. EN 13659 classifies the wind resistance of external blinds and shutters (classes 0–6). The actual permitted wind speed depends on the product, size and installation, so we take the alarm threshold from the manufacturer’s table, not from experience.
  2. Safe position: on alarm, the blind actuator moves the shading into the set position (external venetian blinds and awnings typically up) and blocks further operation until the alarm clears.
  3. Monitored signal: in a well-configured system the actuator does not just wait for “wind present”. A monitoring time can be set in the actuator: if no message arrives from the weather station within it (faulty sensor, interrupted bus), the shading goes to the safe position as well.
  4. Sensor fault: the weather station also monitors itself. According to one manufacturer’s description, if the measured wind speed hardly changes for 48 hours, the station reports a fault, which triggers the wind alarm.
  5. Rain and frost: awnings and screens are also retracted in rain if the manufacturer requires it. The frost alarm comes with cold and precipitation together and blocks movement, so a frozen shutter or blind is not damaged.

What happens in a power cut?

There are two different cases, and both must be planned for:

  • Mains failure (no 230 V): blind and shutter motors run on 230 V and stop where they are without power. A lowered blind stays down, and if a storm comes meanwhile, nothing retracts it. An uninterruptible KNX bus power supply does not help here: it keeps the control alive, not the motor.
  • KNX bus failure (230 V present, no bus voltage): the blind actuator can be parameterised for what the output does then (stop, raise or lower the shading) and after bus voltage returns.
  • Recovery: after a power cut the system does not automatically “remember” everything. We test the behaviour at handover and record it in the handover report.

In practice: with a storm warning or a longer absence, lowered blinds and awnings should be raised in advance (this can be automated), and the wind alarm threshold should not be set close to the manufacturer’s limit. If the motors themselves must be backed up, that is a separately designed (battery, inverter) solution.

Manual operation: what works if something fails?

KNX is decentralised: if a pushbutton or the weather station fails, the other devices keep working. Wall pushbuttons, however, are on the bus themselves and send no commands without it. That is why a manual option always remains:

  • Manual operation on the actuator: most KNX blind actuators have manual buttons in the distribution board that move the shading without the bus.
  • Blocking during alarms: during a wind alarm, manual commands may also be blocked. We explain this to the residents at handover so they do not take it for a fault.
  • Documentation: the ETS project file and the device list belong to the client, so any KNX integrator can continue the work.

What has to be decided before plastering?

  1. Motor cable to every shading product up to the board or actuator position (up, down, neutral, protective earth), led into the shutter box or to the blind guide rail, coordinated with window installation.
  2. KNX bus cable to the pushbuttons and to the weather station position, together with the power supply the manufacturer specifies.
  3. Weather station position: on the roof or the facade, with a clear view, as per the manufacturer’s mounting instructions.
  4. Distribution board: space for the blind actuators and spare for later shading.
  5. Manufacturer data: wind resistance of the blind or awning and the motor type, before the limit values are set.
The shading is supplied and fitted by the shading company; we do the cabling, KNX control, weather station and programming. Individual quote after a site survey or based on the plans.

More: KNX smart home · Smart home · Electrical installation

Frequently asked questions

What are smart blinds?

Motorised shutters, external venetian blinds or awnings controlled by an actuator that move not only from a button but also by schedule, sun position and weather, and protect themselves with a wind alarm.

What does a KNX weather station measure?

Wind speed, precipitation, brightness from several directions, twilight and temperature; more advanced models take time and location from GPS and calculate the sun position.

At what wind speed should external blinds be raised?

Per the manufacturer’s data: EN 13659 classifies the wind resistance of external blinds, but the permitted value depends on the product and size. We set the alarm threshold from the manufacturer’s table.

What happens to external blinds in a power cut?

The 230 V motor stops and the blind stays where it was. Raise it in advance when a storm is forecast or before a longer absence; an uninterruptible bus supply only keeps the control running.

What if the wind sensor fails?

In a well-configured system the actuator monitors the weather station’s signal: if it stops, the shading goes to the safe position. The station also monitors its own wind sensor and triggers the wind alarm on a fault.

Can smart blinds be operated manually?

Yes. Besides the wall buttons, KNX blind actuators typically have manual buttons in the distribution board that work without the bus, as long as mains power is present.

Let’s talk about your project.

Tell us what you are planning and we will get back to you within a few days.

Get in touch

Cookie settings

Choose what you consent to. We remember your choice for 6 months; change it any time via “Cookie settings” in the footer.

Privacy notice