KNOWLEDGE BASE · LOW-VOLTAGE SYSTEMS

PoE: cameras and access points on a single cable. What a PoE switch does, and what to watch as a homeowner

PoE (Power over Ethernet) means the same network cable carries both data and power. An IP camera, a ceiling access point or an IP door station therefore needs no socket on the facade or the ceiling: power comes from the PoE switch in the low-voltage cabinet, at 57 V DC at most. Three things decide whether it works: a dedicated copper Cat6 cable for every device, a channel of no more than 100 m, and a switch that can carry the load per port and in total.

In short

  • One cable, two jobs: the PoE switch supplies data and 44–57 V DC over the network cable. Cameras and access points need no separate socket.
  • Power: PoE (802.3af) delivers about 13 W to the device, PoE+ (802.3at) 25.5 W, PoE++ (802.3bt) 51 or 71.3 W.
  • Length: the channel is at most 100 m (90 m fixed cable + about 10 m of patch cords in total). Beyond that you need fibre or an extender specified by the manufacturer.
  • Cable: solid copper Cat6 or Cat6A. Copper-clad aluminium (CCA) cable is not suitable for PoE.
  • Power cut: if the PoE switch runs on a UPS, cameras and access points keep working.

Author: Norbert Madarász, Managing Director and Partner · Updated: 10 November 2026

What is PoE, and why is it useful in a family house?

An IP camera or an access point needs two things: network and power. Without PoE that means two runs: a network cable and a 230 V socket next to the camera on the facade or ceiling, plus a small power supply. With PoE a single network cable runs to the low-voltage cabinet, and the power arrives on it too.

For the homeowner this brings three benefits: fewer 230 V outlets on the facade and ceiling, power in one place (in the cabinet, where one UPS can keep every camera and access point running through a power cut), and easier extension: a new camera means a new cable to the switch, not a new circuit.

PoE: data and power on one cablePoE switchin the cabinet, on UPSIP cameraon the facadeaccess pointon the ceilingone Cat6 cable per devicedatapower 44–57 V DCWithout PoEswitchcamera+ socket and power supply next to the camerachannel max. 100 m: 90 m fixed + 10 m patch
The PoE switch sits in the low-voltage cabinet and supplies data and power to the camera and the access point over the same cable. The switch output is 44–57 V DC (depending on type); the channel is at most 100 m.

Is the PoE voltage dangerous?

According to the Ethernet Alliance overview, the PoE switch output is 44–57 V depending on the type, with 57 V DC as the upper limit for every type. This falls within extra-low voltage (under HD 60364-4-41: at most 50 V AC or 120 V ripple-free DC). The 230 V side stays inside the switch power supply; the cable is still run according to the rules, separated from 230 V.

PoE, PoE+, PoE++: how much power reaches the device?

PoE is defined by the IEEE 802.3 standard in three steps. The table shows two figures: what the switch delivers at its port, and what reaches the device after the cable losses.

StandardCommon nameAt the switch portAt the devicePairs
IEEE 802.3af (Type 1)PoE15.4 W12.95 W2 pairs
IEEE 802.3at (Type 2)PoE+30 W25.5 W2 pairs
IEEE 802.3bt (Type 3)PoE++60 W51 W2 or 4 pairs
IEEE 802.3bt (Type 4)PoE++90 W71.3 W4 pairs
How much power reaches the device?at the switch portat the devicePoE · 802.3af (Type 1)15.4 W12.95 WPoE+ · 802.3at (Type 2)30 W25.5 WPoE++ · 802.3bt (Type 3)60 W51 WPoE++ · 802.3bt (Type 4)90 W71.3 Wthe difference is lost in the cable
IEEE 802.3 PoE types according to the Ethernet Alliance overview. The device datasheet states its PoE class or maximum consumption; the switch must cover it per port and in total.

The device datasheet states its PoE class (Class 1–8) or its maximum consumption. A fixed IP camera or a typical access point usually manages with PoE or PoE+; a pan-tilt-zoom (PTZ) camera with a heater, a high-performance access point or a door station with a display may need PoE++. The datasheet of the specific device always decides.

What size PoE switch do you need? The PoE budget

A PoE switch has to meet two figures: the demand of the largest device per port, and the demand of all devices in total. The latter is the PoE budget, and on many switches it is less than the number of ports multiplied by the port power. An 8-port PoE+ switch may not be able to power eight 30 W devices at the same time.

Worked example

Four cameras are PoE Class 3 (at most 15.4 W at the switch port), two access points are Class 4 (at most 30 W). The required budget: 4 × 15.4 + 2 × 30 = 121.6 W. You need a switch with at least this PoE budget, and it is worth choosing one with reserve so a later camera or access point also fits.

If the budget is too small, the switch shuts down some ports according to the manufacturer’s settings, and the last device to start gets no power or keeps restarting. Such faults are intermittent and hard to find, so we calculate the budget in the design, not on site.

For a single device (for example a camera added later) a PoE injector is enough: it sits between the switch and the device and powers only that one cable. Many video recorders (NVRs) have built-in PoE ports; larger systems need a separate PoE switch. More on cameras: CCTV installation.

Which cable does PoE need, and how long can it be?

PoE uses the same network cable as the data, so the structured cabling rule applies: the channel is at most 100 m, of which the fixed cable in the wall is at most 90 m and the patch cords together about 10 m (Fluke Networks). If a camera is further away (a gate at the end of the plot, an outbuilding), you need fibre or an extender (PoE extender) specified by the manufacturer.

  • Solid copper conductors: part of the PoE current turns into heat in the cable. According to Fluke Networks, a copper-clad aluminium (CCA) conductor has about 55% more resistance than copper of the same diameter, so it heats up more and less voltage reaches the device. CCA cable does not comply with the standards.
  • Cat6 or Cat6A: both are fine for PoE; for many high-power devices or if 10 Gbit/s is needed, Cat6A. Details: network cabling: Cat6 or Cat6A.
  • Outdoors: UV-resistant outdoor cable in conduit; a small loop below the camera so water does not run into the connector. On conduits: which conduit goes where.
  • Separate from 230 V: we run the network cable in its own conduit, not alongside 230 V wiring.

Passive PoE, injectors, extenders: what to watch?

A standard PoE switch does not put voltage on the cable straight away: it first checks whether a standard PoE device is at the other end, and which class it is. That is why a laptop or TV plugged into a standard switch is not damaged.

Passive PoE (often a 24 V injector) does not check: it puts voltage on the cable all the time. It is used for older or purpose-built devices; connected to a standard device it can cause damage. If such an injector comes in the box, check the device datasheet for the PoE it requires.

Good practice: only standard (802.3af/at/bt) PoE in one system, from one switch, the cameras in a separate network segment (VLAN), default passwords changed, remote access via VPN.

What to ask your installer for

  1. Device list at the start of the design: how many cameras, access points and door stations, and where. This determines the number of cables and the PoE budget.
  2. A dedicated cable for every device to the low-voltage cabinet, solid copper Cat6 or Cat6A, in a star; with spares at important locations.
  3. PoE budget calculation: the switch copes per port and in total, with reserve.
  4. UPS in the cabinet if the cameras must keep recording during a power cut.
  5. Testing and labels: every cable labelled at both ends, test results handed over port by port.
We plan low-voltage systems exactly like power: device list, routes, cabinet, testing. Individual quote after a site survey or based on the plans.

More: Low-voltage systems · CCTV installation · Wi-Fi throughout the house · Network cabling: Cat6 or Cat6A

Frequently asked questions

What is PoE?

Power over Ethernet: the network cable carries power as well as data. The PoE switch supplies at most 57 V DC, so a camera or access point needs no separate socket.

What is the difference between PoE and PoE+?

Power. PoE (IEEE 802.3af) delivers 15.4 W at the switch port, of which about 13 W reaches the device; PoE+ (802.3at) delivers 30 W, of which 25.5 W reaches the device. PoE++ (802.3bt) provides 60 or 90 W at the port.

How far can a PoE camera be from the switch?

The channel is at most 100 m, of which the fixed cable in the wall is at most 90 m. Longer distances need fibre or an extender specified by the manufacturer.

What size PoE switch do 4 cameras need?

Calculate from the cameras’ PoE class. Four Class 3 cameras need a PoE budget of at least 4 × 15.4 = 61.6 W, plus reserve; if access points are added, add their power too.

Is any network cable fine for PoE?

No. You need solid copper Cat6 or Cat6A. Copper-clad aluminium (CCA) cable has higher resistance, heats up more and does not comply with the standards.

What happens to a PoE camera in a power cut?

If the PoE switch (and the recorder) run on a UPS, the cameras keep working for as long as the UPS lasts. Without PoE every camera would have its own power supply, which makes this much harder.

What is passive PoE?

A non-standard solution that puts voltage on the cable permanently, without checking. Connected to a standard device it can cause damage; in one system it is best to use only standard 802.3af/at/bt PoE.

Let’s talk about your project.

Tell us what you are planning and we will get back to you within a few days.

Get in touch

Cookie settings

Choose what you consent to. We remember your choice for 6 months; change it any time via “Cookie settings” in the footer.

Privacy notice