KNOWLEDGE BASE · LOW-VOLTAGE SYSTEMS

Weak Wi-Fi in the house? Extender, mesh or cabled access points: which one when

A Wi-Fi extender repeats the weak radio signal, mesh units keep in touch with each other by radio, and a cabled access point gets its data from the network cable, and its power via PoE as well. In a new house or a full renovation the best choice is a ceiling access point on a cable, at least one per floor; where there is no cable, mesh; the extender is an emergency fix. The decision is made before plastering, because the cable has to be in place by then.

In short

  • Extender (repeater): a cheap, quick fix for a weak corner, but it can only pass on what reaches it from the weak signal.
  • Mesh Wi-Fi: several units with one network name, linked by radio; good where there is no cable. If the units can also be cabled, it is faster and more stable.
  • Cabled access point: on the ceiling, on a network cable and PoE; the most stable option, and what we design into new houses.
  • How many: by our rule of thumb, one per approx. 40–60 m² in a house with brick or concrete walls, one per approx. 70–90 m² in open spaces with drywall, and at least one per floor.
  • Cable first, device later: the access point can be replaced in a few years, the cable in the wall cannot.

Author: Norbert Madarász, Managing Director and Partner · Updated: 10 November 2026

Why is the Wi-Fi weak at one end of the house?

The provider’s router usually sits where the line enters the house: in the hall, the garage or at the bottom of a cupboard. From there the signal has to pass through walls and floors. Brick, reinforced concrete, metal surfaces and underfloor heating pipes all weaken it; the more of them in between, the slower the connection at the far end of the house and upstairs.

Of the Wi-Fi bands, 2.4 GHz reaches further but is slower and crowded, 5 GHz is faster but more attenuated by walls, and 6 GHz (Wi-Fi 6E and Wi-Fi 7) is faster still with an even shorter range. A single powerful router therefore rarely covers a multi-storey house with solid walls well; several smaller, well-placed points are the answer.

Extender, mesh, access point: what is the difference?

The three solutions differ in where the second (or third) Wi-Fi point gets its data from:

Where does the second Wi-Fi point get its signal?Wi-Fi extender (repeater)routerextender→ repeats the weak radio signalMesh with wireless backhaulmesh 1mesh 2→ shares the radio band with your phonesCabled access point (PoE)switchaccess point→ gets data and power over the cableradiocable
An extender and a wireless mesh use the same airtime as your phones; a cabled access point gets its data from the network cable (and its power via PoE). According to TP-Link, a wired backhaul is faster and more stable and uses no wireless bandwidth.
SolutionWhere the data comes fromAdvantageDrawbackWhen it fits
Wi-Fi extender (repeater)from the router’s weak radio signalcheap, plugs into a socketonly passes on the weak signal it receives; often a separate network namea single weak corner, temporarily
Mesh with wireless backhaulfrom the other mesh unit, by radioone network name, easy setupthe link occupies radio bandwidthexisting houses without cabling
Mesh or access point on a cablefrom the network cablefastest and most stable, no socket needed with PoEneeds a cable to every pointnew houses, full renovations

According to TP-Link’s description of its Deco mesh system, a wired link (Ethernet backhaul) is faster and more stable than a wireless one and uses none of the wireless bandwidth your devices would otherwise share. Dual-band mesh units share the 5 GHz band between the link and the connected devices; tri-band units reserve a separate band for the link.

Mesh Wi-Fi: when is it enough, and when not?

  • Enough: in an existing, finished house where no cable can be pulled; one floor, a few walls; or if some of the mesh units can be cabled.
  • Not enough: if the wireless link itself has to pass through several solid walls or a concrete floor, because then the mesh unit receives a weak signal and passes that on.
  • Mixed: cabled units connect by cable, the others by radio. In existing houses this is often how we reach the basement, the upper floor or the terrace.
For the user, cabled mesh and cabled access points are the same: several points, one network name, and the phone switches between them by itself. The difference lies mainly in the product family and the management interface.

Cabled ceiling access points: how we plan them

  • How many: by our rule of thumb, one per approx. 40–60 m² with brick or concrete walls, one per approx. 70–90 m² in open spaces with drywall, and at least one per floor. This is not a value from a standard: the final number depends on the wall materials and an on-site survey.
  • Where: on the ceiling, towards the middle of the area to be covered; not in a corner, not behind a metal cabinet. Garden and terrace need an outdoor access point.
  • Cable and power: one Cat6 cable from each access point to the low-voltage cabinet; power comes from a PoE switch, so no socket is needed on the ceiling. More: PoE switch and PoE cameras, network cabling: Cat6 or Cat6A.
  • One network name: the same network name and password on every access point; a common controller (for example Omada or UniFi) manages them and helps devices hand over between them.
  • The provider’s router: when your own access points broadcast the Wi-Fi, we switch off the Wi-Fi of the provider’s box so it does not interfere.

UniFi (Ubiquiti) Wi-Fi in a family house: what to watch

UniFi is Ubiquiti’s networking range: ceiling and outdoor access points, switches and routers (gateways, in the manufacturer’s terms). The access points are managed by the UniFi Network application, which runs on the manufacturer’s console (for example a Cloud Gateway); every access point can then be set up with one network name, from one interface. We install UniFi networks too.

  • Cable and power: a UniFi access point also needs a network cable and PoE power. Whether PoE or PoE+ is required is stated in the datasheet of the specific model; we calculate the switch’s PoE budget from it. More: PoE switch and PoE cameras.
  • Console and router: the management application runs on the manufacturer’s console, so in a UniFi network it is worth choosing the router (gateway) from the same family; the provider’s box then works, where possible, as a modem only (bridge mode).
  • Cameras too: if you also need cameras, UniFi Protect manages them and stores footage locally on a console that supports recording. More: CCTV installation.
  • Alternative: TP-Link Omada has a similar structure. The choice depends more on the interface and existing devices than on Wi-Fi speed; the ceiling cable is the same for both.

Wi-Fi 6, 6E, 7: which one do you need?

Under the Wi-Fi Alliance generation names, Wi-Fi 6 is IEEE 802.11ax, Wi-Fi 6E is the same extended to the 6 GHz band, and Wi-Fi 7 is IEEE 802.11be, using the 2.4, 5 and 6 GHz bands. In the European Union the lower 6 GHz band (5945–6425 MHz) has been available for Wi-Fi since Decision (EU) 2021/1067.

For a homeowner the generation matters less than the cable: the access point can be replaced with a newer one in a few years, while the Cat6 or Cat6A cable in the wall stays. If the cable is on the ceiling, any generation can be mounted.

What to decide before plastering

  1. Access point positions on the ceiling plan: per floor, alongside lights and ceiling fittings.
  2. A cable to every point, plus spare cable or empty conduit to the attic, the terrace and the garden.
  3. A low-voltage cabinet for the PoE switch and the router, with a UPS.
  4. The provider’s entry point: where the internet line enters, and how it reaches the cabinet.
  5. Testing at handover: cables port by port, Wi-Fi coverage room by room.
Existing houses have solutions too: existing conduits, suspended ceilings, trunking, and mesh units where no cable can reach. Individual quote after a site survey or based on the plans.

More: Low-voltage systems · PoE switch and PoE cameras · Network cabling: Cat6 or Cat6A · CCTV installation

Frequently asked questions

Which is better: a Wi-Fi extender or mesh Wi-Fi?

Usually mesh: one network name, and your phone switches between the points by itself. An extender only passes on the weak signal it receives. If cabling is available, cabled mesh or access points are best.

How many access points does a family house need?

By our rule of thumb, one per approx. 40–60 m² with brick or concrete walls, one per approx. 70–90 m² in open spaces with drywall, and at least one per floor. The exact number depends on the walls and an on-site survey.

Where should the access point go?

On the ceiling, towards the middle of the area to be covered. Corners, metal cabinets and floor level are poor positions, because part of the signal goes outside or into the floor.

Does a ceiling access point need a socket?

No, if it is powered from a PoE switch: the same network cable carries data and power.

What is the difference between a router and an access point?

The router connects the house to the internet and assigns addresses to devices. An access point only makes the wired network available by radio; one router can have several.

Can cabled access points be added later?

Yes: through existing conduits, in a suspended ceiling or in trunking. Where no cable can reach, a mesh unit with a wireless link can be used.

Let’s talk about your project.

Tell us what you are planning and we will get back to you within a few days.

Get in touch

Cookie settings

Choose what you consent to. We remember your choice for 6 months; change it any time via “Cookie settings” in the footer.

Privacy notice