E-MOBILITY · TOYOTA HOME CHARGING

Toyota bZ4X home charging: wallbox installation for family homes

From model year 2025 the Toyota bZ4X charges at home on three phases at 11 kW, so the usual 3×16 A wall charger is enough; the 73.1 kWh battery can be ordered with a 22 kW on-board charger, which needs a 3×32 A connection. Earlier model years may, depending on equipment, have a 6.6 kW single-phase charger; we check this from the factory data sheet or the order equipment list. As an independent electrician we choose and set up the charger for the car and the house supply, build the circuit and, if needed, handle the capacity increase with the utility. We are not an official Toyota partner; we hand over the installation with protection tests and a test report.

How fast does a Toyota bZ4X charge at home?

From model year 2025 the bZ4X charges on AC at 11 kW on three phases (3×16 A), so on a wall charger it goes from 0 to 100 % in about 6 to 7.5 hours, depending on the battery. The 73.1 kWh battery can also be ordered with a 22 kW on-board charger.

VersionMax. AC chargingPhases × currentUsable battery0–100 % at 11 kW
bZ4X (from model year 2025)11 kW3×16 A54–69 kWh (depending on battery)approx. 6 h – 7 h 30 min
bZ4X 73.1 kWh with 22 kW option22 kW3×32 Athe larger batteryshorter at 22 kW
bZ4X earlier model years6.6 kW (single phase) or 11 kW, depending on equipmentsingle phase or 3×16 A–checked from the equipment

Source: ev-database.org. One night (8 hours) at 11 kW gives about 88 kWh, which fills any bZ4X battery; in daily use you rarely charge from empty.

Do I need a 22 kW charger for a Toyota bZ4X?

It only makes sense if the car has the 22 kW on-board charger (an option for the 73.1 kWh battery) and the house supply can handle it. A bZ4X with the 11 kW on-board charger does not charge faster on a 22 kW wallbox than on an 11 kW one.

22 kW needs a 3×32 A charging circuit: a thicker cable, a larger breaker and, because the house has to supply its other loads at the same time, often a capacity increase and load management. Since one night at 11 kW fills the car completely, an 11 kW connection is enough at home in most cases; 22 kW is useful if you need to add a lot of charge during a short stop in the daytime. The Smart #1 Pro+ and Premium, for example, charge at 22 kW from the factory; the same considerations apply there.

What about an earlier model-year bZ4X?

Earlier model years may, depending on equipment, have a 6.6 kW single-phase on-board charger; we check this from the factory data sheet or the order equipment list. It matters because a single-phase car gets only one 16 A phase from a three-phase wallbox set to 3×16 A, which is about 3.7 kW: just over half of the possible 6.6 kW.

For the full 6.6 kW the wallbox must deliver 32 A on one phase, and the house must be able to supply it: the meter needs a main fuse of at least 32 A on that phase, which on the common 3×16 A connection often means a capacity increase. If a three-phase car also charges at the house, we choose a three-phase charger that can also deliver 32 A on one phase. The situation is similar for the single-phase versions of the MG4 and for the 44.9 kWh BYD Dolphin.

Do I need a Toyota wallbox, or does any wall charger work with the bZ4X?

Any Type 2 wall charger works: the bZ4X sold in Europe uses Type 2 for AC charging and CCS2 for DC fast charging. A home wallbox is AC, so it has a Type 2 connector; the charging speed is limited by the car’s on-board charger, not by the brand of the charger.

What matters is the charger’s power and setting: 3×16 A for an 11 kW bZ4X, 3×32 A for a 22 kW one, and 32 A on one phase for an older car with a single-phase on-board charger. With a tethered wallbox you do not need a separate cable at home.

Which wall charger should I choose for a Toyota bZ4X?

A Type 2 wallbox that matches the car’s on-board charger: an 11 kW charger for an 11 kW car, and a 22 kW charger for a car ordered with the 22 kW option, if the house supply allows. Through our wholesale partners we can source and install several brands:

BrandModelSourced via
Schneider ElectricEVlink Home, EVlink Charge ProMile Kft.
ABBTerra AC (W4–W22)Mile Kft.
BesenWallbox Smart 11/22 kWMile Kft.
FroniusWattpilot Home 11/22 kWMile Kft.
TeslaWall Connector Gen 3Mile Kft.; charges other brands too if enabled
HagerwittyVoltus
EaseeChargeVoltus

We check the power and phase settings of the chosen model in the manufacturer’s data sheet before recommending it for a given bZ4X. More on the Tesla Wall Connector on our Tesla home charger page.

What does the house need for a Toyota wall charger?

ElementWhy it is neededWhat we check
Supply and phasesan 11 kW bZ4X needs 3×16 A, a 22 kW one 3×32 A, an older single-phase one 32 A on one phasenumber of phases and main fuse at the meter
Capacitythe charger draws close to full current for hours alongside the other loadsif it is not enough, we request an increase from the distribution operator (E.ON, MVM or Opus Titász)
Dedicated circuit and cablethe charger cannot share its circuitits own breaker; the cross-section depends on the current and the length of the run, thicker for 22 kW
Residual current device (RCD)the car can cause DC fault currents that a standard type A RCD does not detecttype A-EV or B, depending on the charger’s built-in DC detection
Load managementthe oven or the heat pump may run while the car chargeswe set the charger’s current limit to the house
Solar chargingdaytime surplus goes into the car instead of the grida wallbox or control that follows the current PV output
Cable route and locationgarage, carport or fence; it has to work in rain and frostIP rating, cable routing, buried cable if needed

Rules and cost factors are described on our EV charger installation page; if the meter cabinet or the distribution board also needs replacing, see electrical installation. In a new house we plan the charger cable and the board space during electrical design.

How much does Toyota charger installation cost, and is there a grant?

The installation price depends on the cable run, the condition of the distribution board and whether a capacity increase is needed; a 22 kW installation costs more. Indicative prices are on our EV charger installation page; we give an exact quote after a site survey or from photos of the meter cabinet and the distribution board. The quotation lists the charger, the installation and the paperwork on separate lines. You can send photos via the details on our contact page.

There is no state grant for private home chargers in October 2026, and there has never been a dedicated programme: the E-AUTO-2021 residential scheme only supported buying the car.

How does a Toyota charger installation work?

  1. 1
    Survey or photos

    We ask about the car’s model year, battery and on-board charger (6.6, 11 or 22 kW), and check the meter (phases, main fuse), the distribution board and the cable route. In simpler cases, photos of the meter cabinet and the board are enough for a first quotation.

  2. 2
    Quotation and choice of charger

    A charger matching the car’s on-board charger, cable, protection, board extension and paperwork on separate lines.

  3. 3
    Paperwork

    If needed, notification or capacity increase with the distribution operator; the installation date then follows the utility’s procedure, which takes several weeks, sometimes a few months.

  4. 4
    Installation

    Dedicated circuit from the main board, sized cable, circuit breaker and a suitable RCD, mounting the charger. The installation itself is usually short.

  5. 5
    Commissioning and handover

    Setting the charger’s phase configuration and current limit for the bZ4X and the house, a test charge, protection tests and test report, and a walk-through.

Frequently asked questions

Do you install a charger for a Toyota bought from wallbox.hu or another web shop?

Yes. We install Type 2 wall chargers bought from wallbox.hu or any other web shop for a Toyota too: we build the circuit, mount and commission the charger, and hand over the electrical safety test report. It is worth checking with us before you buy: the bZ4X charges at 11 kW three-phase from 2025; for older cars we check the factory data sheet.

Which charger does the Toyota bZ4X need?

Any Type 2 wall charger. The bZ4X built from 2025 charges at 11 kW on three phases, for which a 3×16 A wallbox is enough; the 22 kW on-board charger available for the 73.1 kWh battery needs a 3×32 A connection.

How long does a bZ4X take to charge at home?

On an 11 kW wall charger it takes about 6 to 7.5 hours from 0 to 100 %, depending on the battery (ev-database.org), so one night is more than enough.

Is a 22 kW charger worth it for the bZ4X?

Only if the car has the 22 kW on-board charger and the house supply can handle it. For overnight charging at home 11 kW is usually enough, and a 22 kW connection needs a thicker cable and often a capacity increase.

Why does my older bZ4X charge slowly on a three-phase wallbox?

If the car has a single-phase 6.6 kW on-board charger, a charger set to 3×16 A gives it only about 3.7 kW. For the full 6.6 kW the charger has to deliver 32 A on one phase, and the house supply has to allow it. We check the equipment from the factory data sheet or the order equipment list.

Can I charge a bZ4X from a normal socket?

Occasionally, with a portable charging cable, yes, but it is slow (about 2.3 kW), and a standard socket and circuit are not made for hours of near-full load. For regular charging we recommend a wall charger on a dedicated circuit.

Are you an official Toyota partner?

No. As an independent electrician we install wall chargers for electric cars of any brand to the electrical standards, with protection tests and a test report.

Is there a grant for home chargers?

In October 2026 there is no open state grant for private home chargers; the E-AUTO-2021 residential scheme also only supported buying the car.

Let’s talk about your project.

Tell us what you are planning and we will get back to you within a few days.

Get in touch

Cookie settings

Choose what you consent to. We remember your choice for 6 months; change it any time via “Cookie settings” in the footer.

Privacy notice