Garden and outdoor lighting: what to decide before the landscaping
Good garden lighting does not start with the luminaire but in the ground: the cable runs in conduit on a sand bed, the circuit goes through a 30 mA RCD, the luminaires’ IP rating suits the location, and control is by dusk sensor, timer or motion sensor. All this has to be decided before paving, turfing and facade insulation, because afterwards every new light means digging. This article covers the electrical side; we install garden and facade lighting ourselves.
In short
- Cable: buried cable or cable pulled into conduit, on a sand bed, with warning tape; a spare conduit for later extensions.
- Protection: lighting circuits and outdoor sockets in a home are protected by a 30 mA RCD (HD 60364-4-41:2017).
- IP rating: IP44 on the wall, IP65 in the garden, IP67 or IP68 for ground-recessed lights – always per the datasheet.
- Control: dusk sensor or astronomical timer, a motion sensor at the entrance, KNX or Casambi in a smart home.
- When: cables go in before paving, turfing and facade insulation.
Author: Norbert Madarász
, Managing Director and Partner · Updated: 14 November 2026
Buried cable, conduit, trench: how power reaches the light
Two solutions are usual. Buried cable (e.g. NYY-J) is made for direct burial; other cables may only go into the ground in conduit. We pull garden circuits into conduit even when buried cable is used: the cable can be replaced later, and a cut cable does not mean digging up the whole route.
- Trench: sand bed below and above the conduit, warning tape above; depth according to the design and the Hungarian standard MSZ 13207, so that it cannot be reached by digging or landscaping.
- Conduit: outdoor, buried-grade conduit with a draw wire; wide bends so the cable can be pulled later. Conduit types: electrical conduit types.
- Joints: preferably none in the ground; where needed, accessible, in an outdoor junction box or in the base of the luminaire.
- Spares: an empty conduit to the gate, the garden tap, the garden shed – for a gate opener, a camera or a later light.
- Route drawing: we record conduit positions with photos and a dimensioned drawing so nobody digs through them later.
IP rating: which luminaire goes where?
The first digit of the IP code is protection against solids and dust, the second against water. The minimum for outdoor luminaires comes from the standard part for outdoor lighting (HD 60364-7-714); in practice we choose higher, because garden lights get sprinkled, snowed on and frozen.
| Location | Usual rating | Note |
|---|---|---|
| Covered entrance, under the eaves | IP44 | against splashing water |
| Facade, exposed wall | IP54–IP65 | driving rain, dust |
| Garden, near sprinklers | IP65 | against water jets |
| Ground-recessed, walk-over light | IP67 or IP68 | temporary or permanent flooding; walk-over capability comes from a product to IEC/EN 60598-2-13 |
Ground-recessed lights get a gravel bed or drainage so they do not stand in water, and we check the surface temperature where children or pets walk over them.
RCD, separate circuit, extra-low voltage
Under HD 60364-4-41:2017, lighting circuits in a single household, sockets up to 32 A and mobile equipment used outdoors are protected by an RCD of at most 30 mA. Garden and facade should have their own circuit, independent of the rest of the house: a flooded garden light then does not switch off the indoor lighting. RCD types: RCD types.
| System | Advantage | What to watch |
|---|---|---|
| 230 V garden lights | long runs, high power, wide choice of luminaires | buried cable or conduit, IP, RCD, proper joints |
| 12/24 V extra-low-voltage system (SELV) | better for shock protection, lights easy to move | safety transformer accessible and protected; shorter runs and thicker cable because of voltage drop; the transformer’s 230 V side still needs RCD protection |
Dusk sensor, timer, motion sensor
- Dusk sensor: switches by daylight; the sensor must not see its own lights or it keeps switching on and off.
- Astronomical timer: no sensor, switches by the local sunset and sunrise table; with a programmed switch-off at night.
- Motion sensor: at the drive, the gate and the bin store; decorative light from dusk to midnight, security light only on motion.
- Smart home: in a KNX house the garden is part of the home control (scenes, remote control, linked to the alarm); for retrofits Casambi is an option.
Light pollution is worth considering too: downward, shielded luminaires, warm white light and switching off at night. Light into the neighbour’s window and the sky serves neither the garden nor neighbourly relations.
Outdoor lights with motion sensor: Rábalux, EGLO, Kanlux
An outdoor wall light with a built-in sensor is the most common garden purchase. Whatever the brand, we check these before installation:
- IP rating: at least IP44 under a covered entrance, IP54–IP65 on an open facade, as stated on the label.
- Mounting height and direction: the sensor's range and angle apply at the height given by the manufacturer; mounted too high or facing the wrong way it either misses people or reacts to street traffic.
- Settings: most types let you set the light threshold (dusk), the run-on time and the sensitivity; we set them on site, at dusk.
- Wiring: the same as indoors (L, N, PE), but the circuit runs through an RCD and the cable is laid before the facade insulation. The wall switch stays on, otherwise the sensor does not work either.
- Solar version: no wiring needed, but it gives less light in winter and on a shaded wall.
We also install outdoor lights bought elsewhere; for indoor wiring see how to connect a light fitting.
Facade and entrance lighting
- Insulated facade: the light is fixed through the insulation on a thermally separated mounting element, with cable and box placed before the insulation goes up. Adding an outlet to rendered insulation later means opening it up.
- Up-and-down wall lights, wall washers: the light shows off the facade material; the final positions are marked from the facade drawing.
- House number, entrance, steps: step lighting cable before tiling; house-number lighting can share a box with the doorbell or camera.
- Feature lighting: trees, hedges, ponds – with recessed or spike spots and accessible joints.
What to decide before landscaping
- Light positions: path, drive, terrace, trees, facade – together with the landscaper’s plan.
- Circuits and control: how many circuits, what goes on at dusk, what on motion, what manually; KNX or Casambi in a smart home.
- Conduits and spares: conduit to every light, plus empty conduits to the gate, shed, camera and garden sockets.
- Outdoor sockets: for the mower, Christmas lights, a pond pump – lidded IP44 sockets with 30 mA RCD protection.
- Distribution board: room for the garden circuits, the dusk sensor and the timer.
The landscaper can then pave, plant and turf over the conduits. In a new house this is part of the electrical design; in an existing house we plan it after a site visit.
Garden lighting installed by MDRSZ Elektro
We take on garden, facade and entrance lighting in full: from marking the route and laying cable to connecting the luminaires and setting up the controls, in new and existing gardens. We also help choose luminaires from the datasheets (IP rating, light colour, flicker-free driver).
Related: LED lighting and lighting control · Electrical installation · Connecting a light fitting
Frequently asked questions
Which cable for garden lights?
A cable made for direct burial (e.g. NYY-J), or a cable pulled into outdoor conduit. We put buried cable into conduit too, so it can be replaced later.
How deep should the garden cable be?
The depth follows the design and the relevant standard (MSZ 13207 in Hungary), with sand bedding and warning tape, so it cannot be reached during landscaping.
Do garden lights need an RCD?
Yes. Lighting circuits in a home and outdoor sockets are protected by an RCD of at most 30 mA (HD 60364-4-41:2017). A separate garden circuit is advisable.
Which IP rating do garden lights need?
IP44 under cover, IP54–IP65 on an exposed facade, IP65 in the garden, IP67 or IP68 for ground-recessed lights – always according to the datasheet.
Is 12 V garden lighting better?
It is better for shock protection and the lights are easy to move, but voltage drop means shorter runs and thicker cable. In a large garden or with many lights, 230 V is simpler.
When should garden lighting be planned?
Before paving, turfing and facade insulation, together with the landscaper’s plan. Afterwards every new cable means digging.
How do you set up an outdoor light with a motion sensor?
On most types three things can be adjusted: the light threshold (how dark it must be), the run-on time and the sensitivity. It is best set on site at dusk, with the light mounted at the height given by the manufacturer.
Let’s talk about your project.
Tell us what you are planning and we will get back to you within a few days.
Get in touch