WAGO connector or terminal block? Wire joints in junction boxes and distribution boards
Wires in the wall have to be joined somewhere: in a junction box, at a light, in the board. Today this is mostly done with spring or lever connectors (in Hungary simply called “wago”) or terminal blocks. Using WAGO datasheets and HD 60364-5-52, this article shows which connector suits which wire, how much current it carries, and where a joint is allowed in a house at all.
In short
- WAGO 2273: solid wire only, 0.5–2.5 mm², 24 A, 450 V, T60 (datasheet). For junction boxes with solid cable.
- WAGO 221 (lever): solid, stranded and fine-stranded wire; 221-4xx up to 4 mm², 32 A; 221-6xx up to 6 mm², 41 A. For lights where flexible wire is involved.
- Terminal block: on a DIN rail, in the board or plant room, with screw, spring or push-in connection.
- Joints only where accessible: in a box, under a cover – no joints buried in plaster (HD 60364-5-52, 526).
- For all of them: strip length and cross-section per datasheet, wire pushed fully home.
Author: Norbert Madarász
, Managing Director and Partner · Updated: 11 November 2026
WAGO 221, 2273 and terminal blocks: what is the difference?
| Connector | Wire | Cross-section | Current, temperature | Where |
|---|---|---|---|---|
| WAGO 2273 (2–8 poles) | solid only | 0.5–2.5 mm² | 24 A, T60 | junction box, solid cable |
| WAGO 221-4xx (2, 3, 5 poles) | solid, stranded, fine-stranded | 0.2–4 mm² (fine-stranded from 0.14) | 32 A, T85 | lights, mixed wires, junction box |
| WAGO 221-6xx (2, 3, 5 poles) | solid, stranded, fine-stranded | 0.5–6 mm² | 41 A | larger cross-sections |
| Terminal block | by type | by type | per datasheet | DIN rail, board, plant room |
The figures come from WAGO datasheets (IEC/EN ratings, 450 V). “T60” and “T85” mean the connector may be used at ambient temperatures up to 60 or 85 °C – this matters inside luminaires and in warm places.
WAGO 221: lever connector for every wire type
The 221 series is a clamp opened and closed by a lever, with a transparent housing: after inserting the wire you can see whether it is fully home. The 221-412, -413, -415 take two, three and five wires up to 4 mm²; the 221-612, -613, -615 do the same up to 6 mm².
- Fine-stranded wire (luminaire leads, flexible cable) can be connected without a ferrule – the main advantage over the 2273.
- Mixed joints: solid and fine-stranded wires in one connector, which makes it a good choice for lights. On connecting a light: connecting a light fitting.
- The lever reopens, so the joint can be undone; the strip length is given in the datasheet.
WAGO 2273: solid wire only
The 2273 series is a compact push-in connector for solid wire from 0.5 to 2.5 mm². Per the datasheet: 24 A, 450 V, 4 kV impulse voltage, T60, 11 mm strip length. Its small size makes it handy in crowded junction boxes.
- Not for fine-stranded wire: the spring does not hold thin strands reliably. Use a 221 instead.
- Aluminium wire: according to WAGO, solid aluminium can be used, but only with WAGO “Alu-Plus” contact paste and reduced current (16 A on 2.5 mm²). With an old aluminium installation, renewal is usually the better answer: electrical installation.
Terminal blocks: screw, spring or push-in
A terminal block clips onto a DIN rail and is used in distribution boards, plant rooms and control cabinets. DIN-rail terminal blocks are made by WAGO (for example the TOPJOB S family), Phoenix Contact and other manufacturers.
- Screw: the long-established solution; tighten to the manufacturer’s torque and recheck in places with vibration.
- Spring (cage clamp) and push-in: opened without tools or with a screwdriver, they do not loosen; solid wire can be pushed straight into a push-in clamp.
- Main terminals, distribution blocks: for splitting the supply, neutral and protective earth; for larger cross-sections.
In a consumer unit the terminal blocks go on the same rail as the MCBs and RCDs. On boards: distribution board manufacturing; on protective devices: circuit breakers and surge arresters.
Junction boxes: where can a joint be in the wall?
Under section 526 of HD 60364-5-52, every connection must provide durable electrical continuity and adequate mechanical strength and – with a few exceptions (such as joints designed to be buried or compound-filled) – must be accessible for inspection, testing and maintenance. Joints go into an enclosure or box.
- Junction box in the wall or ceiling with a removable cover that stays reachable later (not tiled over, not hidden behind a wardrobe).
- In drywall use hollow-wall boxes; at a light outlet the joint goes into the luminaire’s terminal compartment or a box.
- Twisting and tape do not give a durable, testable joint; the proper solution is a connector or terminal block.
- Manufacturers: junction and flush boxes are made by Kaiser, Kopos and OBO Bettermann among others; the box is chosen for the wall material (brick, concrete, drywall) and the depth needed.
WAGO or terminal block: when to use which?
- Junction box, solid wire: 2273 or 221, depending on the number of wires.
- At a light, fine-stranded wire: 221, or the luminaire’s own terminal.
- Above 4 mm², up to 6 mm²: 221-6xx or a terminal block.
- Board, plant room, control cabinet: DIN-rail terminal blocks, labelled, according to the wiring diagram.
- Always: cross-section and current within the datasheet, wire fully home, joint accessible.
We work with WAGO connectors and OBO products. Before handover the installation is tested, and you receive a test report.
Frequently asked questions
What is the difference between WAGO 221 and 2273?
The 2273 is for solid wire only, 0.5–2.5 mm², up to 24 A. The 221 lever connector takes solid, stranded and fine-stranded wire: 221-4xx up to 4 mm² and 32 A, 221-6xx up to 6 mm² and 41 A (WAGO datasheets).
Are WAGO connectors safe?
Yes, when used within the datasheet: for the right wire type and cross-section, with the given strip length, pushed fully home, and with the joint in a box where it remains accessible.
Can WAGO connectors take fine-stranded wire?
The 221 lever connector can, even without a ferrule. The 2273 is for solid wire only.
WAGO or terminal block in a distribution board?
In a board, DIN-rail terminal blocks are standard, labelled and according to the diagram. WAGO splicing connectors are for junction boxes and lights.
May a joint be plastered over?
No. Under HD 60364-5-52, joints must – with a few exceptions – remain accessible for inspection and maintenance, so they go into a junction box with a cover.
Can aluminium wire be connected with WAGO?
According to WAGO, solid aluminium can go into the 2273 only with “Alu-Plus” contact paste and reduced current. For old aluminium installations we usually recommend renewal.
Let’s talk about your project.
Tell us what you are planning and we will get back to you within a few days.
Get in touch