KNOWLEDGE BASE · LIGHTING

LED dimmer switches: which one, and why does the LED flicker?

An LED needs a dimmer switch that the manufacturer has rated for LED loads, ideally trailing edge or universal – and a light source that is marked as dimmable. LED flicker almost always comes from the two not matching, from too small a load or from a missing neutral. With 12/24 V LED strip, dimming is decided at the driver, not in the wall.

In short

  • Which dimmer for LED? One rated for LED loads, trailing edge (RC) or universal (RLC), and listed on the lamp manufacturer’s compatibility list.
  • Which bulbs are dimmable? Only those marked “dimmable” or with the dimmer symbol on the box. A non-dimmable LED must not be put on a dimmer.
  • How many LEDs per dimmer? Far fewer than incandescent bulbs: the datasheet gives a separate LED load, and a lower limit too.
  • Why does it flicker? Incompatible pairing, running below minimum load, a poor driver, a loose connection or wiring without neutral. See the table below.
  • Wiring: replacing a dimmer is 230 V work, often with changes to the back box. An electrician does it; we do not give a DIY guide.

Author: Norbert Madarász, Managing Director and Partner · Updated: 8 November 2026

Which dimmer switch do LEDs need?

One for which the manufacturer also states an LED load, and which has been tested with the lamp. Most old rotary dimmers made for incandescent bulbs are leading edge, and they often do not get on with LED drivers: they flicker, buzz, or only dim over a small part of the dial.

Decide in this order: first the light source (is it dimmable, which dimming principle does its maker specify), then the dimmer, finally the quantity. Signify (Philips) and Ledvance (Osram) both publish which dimmers they have tested their lamps with, with how many lamps and over what dimming range. Ledvance states explicitly that it does not guarantee operation with dimmers it has not tested.

How do I know if an LED bulb is dimmable?

From the packaging and datasheet: a dimmable LED bulb carries “dimmable” or a dimmer symbol, a non-dimmable one often a crossed-out dimmer symbol or “not dimmable”. If there is nothing on it, treat it as non-dimmable.

  • Non-dimmable LED on a dimmer: its built-in driver is not designed for it; it flickers, blinks, buzzes, and the driver may fail early. Remove the dimmer or change the bulb.
  • Integrated LED fittings: the fitting’s (or the separate LED driver’s) datasheet says whether and how it dims: leading edge, trailing edge, 1–10 V or DALI.
  • “Step-dimming” bulbs: some bulbs change brightness when an ordinary switch is flicked several times. They do not belong on a dimmer.

Leading edge or trailing edge: what is the difference?

Both cut out part of the 230 V sine wave, just on different sides. A leading-edge (RL) dimmer – typically TRIAC-based – delays switching on at the start of each half-cycle; a trailing-edge (RC) dimmer switches off towards the end. LED driver inputs are mostly capacitive, which suits trailing edge better.

TypeMarkingHow it dimsWhat it is for
Leading edgeRL, TRIACdelayed switch-on at the start of the half-cycleincandescent, halogen, wound transformers; LED only if the lamp maker asks for it
Trailing edgeRCswitch-off at the end of the half-cycleelectronic transformers, most 230 V dimmable LED bulbs and drivers
UniversalRLC, “universal”leading or trailing edge to suit the load, automatically or set by handmixed or unknown loads; with LEDs it is worth fixing the mode manually
LED dimmer“LED”, often RCtrailing edge with a minimum level tuned for LEDslow-wattage LED circuits

A wound transformer must not be connected to a trailing-edge dimmer. A universal dimmer’s automatic detection usually gets it right, but with LEDs it sometimes picks the worse mode; many types therefore let you set the mode and the minimum brightness by hand. Schneider Electric notes that RL mode allows deeper dimming with some LEDs – so there is no universal winner; the lamp maker’s recommendation decides.

How many LEDs can go on one dimmer?

Far fewer than incandescent bulbs. LED drivers draw a short current peak at switch-on and, when dimmed, in every half-cycle, so it is this peak that loads the dimmer, not the LED’s nominal wattage. That is why manufacturers give a separate LED rating.

Gira dimmer (example)Incandescent / halogenLED, leading edgeLED, trailing edge
System 3000 universal LED dimmer, 2450 00 (flush-mounted)20–210 Wtypically 3–60 Wtypically 3–120 W
System 3000 universal LED dimmer Mini, 2440 0020–210 Wtypically 3–50 Wtypically 3–100 W
System 3000 LED dimmer Basic RC, 2457 00 (trailing edge only)3–200 W–typically 3–200 W
System 3000 universal LED dimmer, 2365 00 (DIN rail)20–420 Wtypically 3–100 Wtypically 3–400 W

Two things stand out. The maximum LED load in leading-edge mode is a fraction of the incandescent rating, and larger in trailing-edge mode. And there is a minimum load: below it the dimmer’s electronics do not get enough current to run steadily, and the LED flickers or flashes. That is often why a single 4–5 W bulb on a dimmer misbehaves. The manufacturer’s list also shows how many lamps the pairing was tested with – keep to it.

LED strip and 12/24 V lights: where does dimming happen?

At the power supply (LED driver), not on the strip. A 230 V wall dimmer may only go ahead of the driver if the driver is specifically TRIAC-dimmable (phase-cut dimmable). A dimmer in front of an ordinary driver will not dim, and may damage the driver.

  • TRIAC-dimmable driver: works with the existing wall dimmer; handy in a renovation with no other cable in the wall.
  • 1–10 V / 0–10 V: the driver receives the level on a separate control pair; this needs an extra pair of cores to the switch or controller.
  • PWM controller: after a constant-voltage driver, ahead of the strip; with push-button, radio or app control.
  • DALI: a digital bus with addressable brightness and colour temperature per fitting. We cover it separately: DALI lighting control at home.

Decide this before the plasterboard goes up: the driver location and the control cable are hard to add later. More: Hidden LED strip lighting in drywall.

Why does the LED flicker or buzz?

LED flicker almost always comes from dimmer, driver and load not matching, less often from an installation fault. The most common symptoms and causes:

SymptomLikely causeRemedy
Flickers or blinks at low levelsbelow minimum load; the dimmer’s low range does not suit the LEDraise the minimum level on the dimmer; more or different lamps; a compatible dimmer
Dimmer or lamp buzzesleading-edge operation with an LED drivertrailing-edge (RC) mode or dimmer, if the lamp maker allows it
Flickers even at full brightnessnon-dimmable bulb, poor-quality driver, loose connectionreplace with a dimmable bulb; have an electrician check the connections
Glows or flashes when switched offa two-wire (no-neutral) dimmer or illuminated switch draws current through the lampa dimmer with neutral; if not possible, the load correction the maker recommends
Only dims over part of the range, then goes outdimmer and bulb ranges do not matchset minimum and maximum levels; use a listed pairing
Dimmer runs hot, switches offtoo many LEDs; the inrush peak exceeds the LED ratingfewer lamps per dimmer, a dimmer with a higher LED rating, or a power booster
LED strip flickersnon-dimmable driver behind a dimmer, or an unsuitable controllera dimmable driver, or PWM, 1–10 V or DALI control after the driver

If the flicker is also there with an ordinary switch and no dimmer, or several lights flicker at once, do not blame the dimmer: it may be a wiring or supply fault, which needs to be found by measurement.

Does the switch box need a neutral?

For many dimmers, yes. In older Hungarian houses the switch box usually only has the live and the switched wire to the light, no neutral. A two-wire (no-neutral) dimmer then draws its own operating current through the lamp, which can make LEDs glow or flash. The datasheet of Gira’s universal LED dimmer says the same: it works without neutral, but some LED sources need the neutral connected to avoid flicker.

Most smart (Wi-Fi, Zigbee, KNX) dimmers require a neutral anyway. If there is none in the box, the options are a new cable or moving the dimmer (into the distribution board or next to the light) – which needs planning. For smart homes see KNX smart home.

Wiring a dimmer switch: why is it an electrician’s job?

In principle it is a switch swap; in practice it often turns out that the neutral is missing, the box is too shallow, the circuit is two-way or intermediate, or the old cable is not fit for purpose. A wrong connection can cause fire and electric shock, and can defeat the dimmer’s own protection.

Replacing a dimmer is work on the 230 V mains, so we do not give a step-by-step DIY guide or wiring diagram. Have an electrician do it, with isolation and testing. We also match lamps and dimmers using the manufacturers’ compatibility lists, so that the pairing is not found wanting only once it is in the wall.

We replace dimmers, install light fittings and LED strip, and build DALI, Casambi and tunable white systems; we quote on the basis of a site survey or the design. More: LED lighting and lighting control · Electrical installation

Frequently asked questions

Which dimmer switch do LEDs need?

One rated for LED loads, ideally trailing edge (RC) or universal, and listed on the lamp manufacturer’s compatibility list. Old leading-edge dimmers made for incandescent bulbs often flicker or buzz with LEDs.

Why does my LED bulb flicker on a dimmer?

Most often because dimmer and bulb are not compatible, the load is below the dimmer’s minimum, the bulb is not dimmable, or the dimmer is wired without neutral. Less often a loose connection or a poor driver is to blame.

Are all LED bulbs dimmable?

No. Only those marked “dimmable” or with the dimmer symbol on the box. A non-dimmable LED must not be put on a dimmer: it flickers and its driver may fail.

How many LED bulbs can go on one dimmer?

As many as the dimmer’s LED rating and the lamp maker’s compatibility list allow. That is far below the incandescent rating: a Gira universal dimmer rated 210 W for incandescent, for example, typically takes 120 W of LED in trailing-edge and 60 W in leading-edge mode.

Can LED strip be dimmed with a wall dimmer?

Only if the 12/24 V driver is TRIAC-dimmable. Otherwise dimming happens at or after the driver: with 1–10 V, PWM or DALI control.

Can a layperson wire a dimmer?

We do not recommend it. It is 230 V work, the neutral is often missing or the box needs changing, and a wrong connection is a fire and shock hazard. Have an electrician do it.

Let’s talk about your project.

Tell us what you are planning and we will get back to you within a few days.

Get in touch

Cookie settings

Choose what you consent to. We remember your choice for 6 months; change it any time via “Cookie settings” in the footer.

Privacy notice