KNOWLEDGE BASE · LIGHTING

DALI lighting control in a family house: DALI, KNX or Casambi?

DALI lighting control is digital: every luminaire’s driver gets its own address and can be switched, dimmed individually, in groups or as scenes over two wires, and on tunable white luminaires the colour temperature can be set too. In a family house it pays off when there are many dimmed circuits or tunable white luminaires; if the house is built with KNX, a KNX–DALI gateway brings DALI in, and in a finished, occupied house wireless Casambi is often the better route.

In short

  • What is DALI? A two-wire digital bus to IEC 62386 for controlling luminaire drivers. DALI-2 is the DALI Alliance certification programme based on the latest version of the standard.
  • What does one line handle? Up to 64 drivers, 16 groups and 16 scenes; the bus is polarity-free and needs its own power supply.
  • DALI, KNX or Casambi? New house with KNX: KNX plus a KNX–DALI gateway. Lighting only, without KNX: a stand-alone DALI controller. Finished, occupied house or one or two rooms: Bluetooth-based Casambi.
  • Before plastering: DALI luminaires need a five-core cable (L, N, PE plus two DALI cores), and the bus route must be fixed in the design.

Author: Norbert Madarász, Managing Director and Partner · Updated: 10 November 2026

What is DALI control, and how is it different from a dimmer?

DALI (Digital Addressable Lighting Interface) is addressable, digital control of lighting: instead of regulating the luminaire’s supply voltage, we send a command to the driver. A conventional wall LED dimmer chops the 230 V supply, and one dimmer controls one circuit. With DALI every driver stays permanently powered and sets the requested level on a command arriving over the two DALI cores.

  • Individual address: every driver can be addressed separately, so luminaires on the same circuit can run at different levels.
  • Groups and scenes stored in the driver: group and scene settings live in the driver, so a “dinner” scene recalls ten luminaires with a single command.
  • Feedback: the controller can query a driver (e.g. lamp failure), which a plain dimmer cannot do.
  • Vendor independence: thanks to DALI-2 certification, drivers, pushbutton interfaces and sensors from different manufacturers work on one bus.

How is a DALI system built?

A DALI system in a family house has five parts: bus power supply, controller or gateway, drivers, controls and sensors, and commissioning (addressing, groups, scenes). The key bus figures:

ParameterValue per DALI lineWhat it means in practice
Drivers (control gear)up to 64 addressesan average family house usually fits on one line; larger houses on two
Groups / scenes16 / 16rooms, rows of luminaires, moods
Wiring2 cores, polarity-freeswapping the two DALI cores is not a fault
Bus voltage, currenttypically 16 V DC, max. 250 mAthe supply rating also limits the number of devices
Cable lengthmax. 300 m between two devices with 1.5 mm²bus voltage drop must not exceed 2 V; thinner cores mean shorter runs
Shock protectionnot SELVthe DALI cores must run in mains-rated cable
  1. Bus power supply: one per DALI line; many KNX–DALI gateways and controllers have it built in. An ordinary DC power supply is not suitable.
  2. Controller or gateway: a stand-alone DALI application controller, or in a KNX house a KNX–DALI gateway that translates KNX group addresses into DALI commands.
  3. Drivers and dimmers: a DALI LED driver in or next to the luminaire, a DALI constant-voltage dimmer for LED strip.
  4. Controls and sensors: pushbutton interfaces, presence and light sensors, wall panels.
  5. Commissioning: addressing on the bus, setting up groups and scenes, assigning buttons and sensors, then testing room by room.

DT6 or DT8: what does a tunable white LED need?

DALI drivers announce a device type on the bus. DT6 is the single-channel LED driver: one colour temperature, brightness only. DT8 is the colour control driver: the type for tunable white luminaires (adjustable colour temperature, e.g. cool white in the morning, warm white in the evening) and multi-colour (RGB, RGBW) luminaires.

A tunable white luminaire therefore needs a DT8 driver and a controller or gateway that handles DT8. Check this before ordering: if the luminaire contains a DT6 driver, the colour temperature cannot be adjusted, whatever the controller can do.

RGBW and tunable white in practice: what does DT8 need to support?

DT8 (IEC 62386-209) is not a single mode but the umbrella name for several colour control types. In DALI-2 certification the DALI Alliance covers these:

  • Tc (colour temperature): the type for tunable white luminaires; the driver mixes the cool and warm white LED channels to the requested colour temperature.
  • RGBWAF: channel-by-channel control of colour luminaires (red, green, blue, white, and where present amber and a free colour).
  • xy: colour set by chromaticity coordinates; it can only be certified together with the other types, as multi-type colour control.

The fourth type, “primary N”, was not included in certification by the DALI Alliance. In practice: “DT8” on the driver datasheet is not enough; check which colour type it supports and whether the controller or gateway handles the same.

What do the KNX–DALI gateway and the control device need?

TaskKNX object on the gatewayWhat to watch
Set colour temperature2-byte value in kelvin (DPT 7.600)within the luminaire’s colour temperature range
Step colour temperaturerelative dimming object (warmer, cooler)a simple pushbutton needs separate button pairs for brightness and colour temperature
RGB colour3-byte combined object (DPT 232.600) or 1 byte per channelthe control device must support the chosen form too
RGBW colour6-byte combined object (DPT 251.600) or 4 × 1 byteif the pushbutton cannot send 6 bytes, separate objects per channel are needed
HSV colourseparate objects for hue, saturation and brightnessconvenient for colour-wheel interfaces

From our own KNX practice: the gateway may support RGBW and tunable white, yet the setup stalls at the control device. A simple pushbutton rarely sends a combined colour value, so for RGBW we either use separate objects per channel or send the colour from a display or visualisation; for tunable white we assign the buttons so that brightness and colour temperature can be adjusted separately. Many gateways also offer Dim2Warm: when dimmed, the light gets warmer by itself, like a traditional incandescent lamp. Agree on this before choosing luminaires and control devices.

Constant light control: when is it worth it?

Constant light control is a closed control loop: a ceiling light sensor measures the illuminance in the room, and the controller dims the luminaires until the set value (lux) is reached. When the sun comes in, the luminaires dim down; on overcast days or at dusk they add light. This is different from a twilight switch, which only switches at one threshold.

  • With a DALI-2 sensor: DALI-2 has standardised the light sensor (IEC 62386-304) and the occupancy sensor (IEC 62386-303); a combined sensor provides both on the same two cores.
  • With KNX: constant light control often runs in the KNX presence detector or a light controller and dims the DALI groups via the KNX–DALI gateway.
  • Where it pays off in a family house: home office, study, a living room with large glazing or a kitchen worktop where even light is needed. In circulation areas, presence detection is usually enough.
  • Commissioning: the setpoint must be set by measurement on site, in daylight and in the evening, and the sensor must not look directly into a luminaire or a window.

Which switches and sensors connect to the DALI bus?

DALI-2 also standardised control devices: pushbutton interfaces, presence and light sensors. They sit on the same two cores as the drivers.

  • Pushbutton interface: fits in the switch box, with a conventional pushbutton in front. A short press switches, a long press dims.
  • Presence-controlled lighting: a ceiling presence sensor switches on in corridors, walk-in wardrobes, pantries and on stairs, switches off after a set time, and at night only to a dimmed level.
  • Light sensor: reduces the luminaires’ output in rooms with daylight.

DALI, KNX or Casambi: what is the difference?

The three play different roles. DALI is a dedicated lighting bus. KNX is the bus for automating the whole house (lighting, shading, heating) and controls DALI luminaires via a KNX–DALI gateway; such a gateway typically handles 64 DALI devices, 16 groups and DT8 tunable white. Casambi is a wireless mesh system based on Bluetooth Low Energy, handling up to 250 devices per network and working without internet.

AspectDALI (stand-alone controller)KNX + KNX–DALI gatewayCasambi
Cablingfive-core cable to luminaires, DALI cores to buttonsDALI cores to luminaires + KNX bus cable to switchesno separate control cable, only 230 V
Best fornew build, lighting control onlynew build or full renovation with full automationfinished, occupied house, renovation without chasing walls
Scalability64 drivers per line, extend with further linestogether with the KNX system, vendor-independentup to 250 devices per network
Who programs itthe electrician, with the controller softwarea KNX integrator (ETS)installer or owner, from the app
User interfacewall buttons, sensors, controller appwall buttons, KNX visualisation, appCasambi app, wireless buttons

The boundaries are fluid: there are Casambi–DALI controllers (e.g. the Casambi CBU-DCS family) that bring DALI drivers into a Casambi network. For the general comparison of KNX and wireless systems, see our article KNX or wireless smart home?

Which DALI devices do we work with?

We mainly install and supply DALI devices from Lunatone, TCI and Helvar, because they are well-made, reliable products; for wireless systems we use Casambi. The main criterion is that driver, controller and sensor work together under DALI-2, and that the type (DT6 or DT8) matches the luminaire.

ManufacturerTypical devices
Lunatone (Austria)DALI-2 controllers and bus power supplies, push-button interfaces, sensors, gateways
TCI (Italy)DALI LED drivers, including tunable white (DT8) types
Helvar (Finland)DALI control, LED drivers and sensors for larger, multi-line systems
Casambi (Finland)Bluetooth-based wireless control, Casambi–DALI modules

Installation and supply in one hand: we select the drivers and controllers, install and program them. We also supply these devices to electricians and designers who need a DALI driver, controller or sensor for their own project, and help with the choice of type (DT6 or DT8, bus load, power supply).

When is DALI worth it in a family house, and when is it overkill?

DALI pays off when there are many dimmed or tunable white luminaires and scenes and sensors must work reliably for years. We have already built such systems in family houses with DALI, Casambi and tunable white luminaires; our experience is that the decision depends on the number of luminaires and the state of the house, not on fashion.

  • Worth it: open-plan living–kitchen–dining with many downlights and hidden LED strip, tunable white lighting, presence-controlled circulation areas, a KNX house.
  • Overkill: a smaller flat with a few luminaires where dimming is needed in one or two rooms; a good wall LED dimmer or a few Casambi devices are enough.
  • Rather Casambi: an occupied house without five-core cable to the luminaires, where chasing walls must be avoided.

What has to be decided before plastering?

DALI decisions are made before plastering: retrofitting cable is the most expensive item.

  1. Five-core cable to the luminaire positions (L, N, PE plus two DALI cores, e.g. NYM-J 5×1.5) wherever a DALI luminaire may go. The DALI cores may share the mains cable because the bus is not SELV.
  2. Bus route: line, tree or star topology, never closed into a ring; distance and voltage drop must stay within the limit.
  3. Button positions: the pushbutton interface needs DALI cores in the switch box, in a KNX house the KNX bus cable.
  4. Driver positions: for LED strip and recessed luminaires the driver must remain accessible (access hatch, distribution board).
  5. Distribution board: space for the bus power supply, the controller or gateway, and a spare for a second line.
The DALI cores run together with mains conductors, so the installation is electrician’s work to the applicable standards. We quote on the basis of a site survey or the design, and help select luminaires and drivers so that DT6/DT8 and the controller match.

More: LED lighting and lighting control · KNX smart home · Smart home · Low-voltage systems

Related articles from our knowledge base

Updated: 8 November 2026
LED dimmer switches: which one, and why does the LED flicker?

Leading or trailing edge, minimum load, dimmable bulbs and drivers – how to stop LED flicker.

Read →
Updated: 10 November 2026
Human centric lighting (HCL) and tunable white in a family home

Light that follows the time of day: what standards say about non-visual effects, and how to build it with DALI DT8, KNX or Casambi.

Read →
Updated: 14 November 2026
Smart relay, smart switch or smart bulb?

Retrofitting without opening walls: Shelly behind the switch, neutral wire, Wi-Fi or Zigbee, Home Assistant and Philips Hue.

Read →
Updated: 10 November 2026
Kitchen and living room lighting: layers and the pendant over the table

General, task and accent light, the height of the dining pendant, and what to decide before drywall and tiling.

Read →
Updated: 10 November 2026
Choosing DALI drivers and controllers: Lunatone, TCI, Helvar, Tridonic, Casambi

DALI-2, D4i, DT6/DT8, KNX–DALI gateways (MDT, Gira, ABB, Lunatone) – what to check, based on datasheets.

Read →
Updated: 15 November 2026
48 V magnetic track lighting: what to decide before the plasterboard goes up

230 V vs 24/48 V track, run length and power supply, recessed installation in drywall, DALI/KNX control and popular systems from manufacturer data.

Read →
Updated: 14 November 2026
Matter, Thread, Zigbee, Z-Wave or Wi-Fi? Smart home standards

How they differ, whether you need a hub or a Thread border router, what a Matter bridge is, and when KNX or DALI is better.

Read →

The whole knowledge base →

Frequently asked questions

What is DALI lighting control?

Digital lighting control to IEC 62386: every LED driver gets its own address and switches, dims or changes colour temperature on commands arriving over two wires. Groups and scenes are stored in the drivers.

How many luminaires fit on one DALI line?

Up to 64 drivers, organised into 16 groups and 16 scenes. The bus power supply current also limits the actual number. Larger houses get a second line.

Does DALI need a separate cable?

Luminaires need a five-core cable (L, N, PE and two DALI cores). The DALI cores may run in mains cable because the bus is not SELV. This must be decided before plastering.

What is the difference between DALI and KNX?

DALI is a lighting bus, KNX is the bus for automating the whole house. In a KNX house, DALI luminaires are controlled via a KNX–DALI gateway, which typically handles 64 devices, 16 groups and tunable white (DT8).

What is Casambi?

Wireless lighting control based on Bluetooth Low Energy with a mesh structure, up to 250 devices per network. It works without internet, is set up from an app and can be installed in an occupied house without control cables.

What does a tunable white LED need?

A DT8 DALI driver and a controller or gateway that handles DT8. With a DT6 driver only brightness can be adjusted, not colour temperature.

Can an RGBW LED strip be controlled with DALI?

Yes, with a DT8 DALI driver of the RGBWAF colour type and a controller or KNX–DALI gateway that handles RGBW. From KNX, the colour can be sent as a 6-byte combined object or as separate objects per channel; the control device must support the chosen form too.

What is constant light control?

A closed control loop: a light sensor measures the illuminance in the room, and the controller dims the luminaires so that the set lux value is maintained. It dims down in sunshine and adds light on overcast days. It can be implemented with a DALI-2 light sensor, or with a KNX presence detector and a KNX–DALI gateway.

Which manufacturers' DALI devices do you install?

Mainly DALI devices from Lunatone, TCI and Helvar, and Casambi for wireless systems. Thanks to DALI-2 certification, certified devices from other manufacturers also work with them; we always match the type to the luminaire and the control system.

Can I buy DALI devices from you as an electrician or designer?

Yes, we also supply Lunatone, TCI and Helvar devices to electricians and designers. Send us the types or describe the task and we will quote; we can also help you choose the types.

Let’s talk about your project.

Tell us what you are planning and we will get back to you within a few days.

Get in touch

Cookie settings

Choose what you consent to. We remember your choice for 6 months; change it any time via “Cookie settings” in the footer.

Privacy notice