Human centric lighting (HCL) and tunable white in a family home
Human centric lighting (HCL) is smart lighting that adapts the amount and colour temperature of light to the time of day: more and cooler white light during the day, less and warmer light in the evening. Its tool is the tunable white luminaire, typically adjustable between 2700 and 6500 K, controlled by DALI DT8, KNX or Casambi. This article summarises what standards and the literature say and what has to be decided at the design stage. We make no health claims: HCL is a comfort and lighting design solution, not a medical device.
In short
- Tunable white: white light of adjustable colour temperature from the same luminaire, from warm white (approx. 2700 K) to cool white (approx. 6500 K), with dimming.
- Human centric lighting: a design approach, not a product. Besides colour temperature, the amount, direction and timing of light matter, and daylight comes first.
- What the literature says: melanopsin-containing receptors in the eye are also responsible for non-visual effects of light. They are quantified according to CIE S 026/E:2018 (melanopic EDI); a 2022 expert recommendation advises more light during the day and less in the evening.
- Implementation: tunable white LED strip or luminaire, DALI DT8 driver, KNX–DALI gateway or Casambi, time schedule.
- When it is worth it: home office, children’s rooms, homes of older residents, large open-plan living areas; in new builds or full renovations.
Author: Norbert Madarász
, Managing Director and Partner · Updated: 10 November 2026
What are human centric lighting and tunable white?
A tunable white luminaire contains two kinds of LEDs: warm white and cool white. The driver changes their ratio, so the colour temperature can be adjusted continuously along the black-body curve. The typical range in manufacturer datasheets is 2700–6500 K; a 24 V tunable white LED strip from a Swiss distributor, for example, covers 2700–6500 K with colour rendering of Ra > 90.
Human centric lighting (HCL) – also called circadian or biodynamic lighting – goes further: lighting design that takes the non-visual effects of light into account as well as vision. In practice this means brightness and colour temperature that change with the time of day, on a schedule or following daylight.
| Term | What it means | Good for |
|---|---|---|
| Dimmable LED | only brightness is adjustable, colour temperature is fixed | mood lighting, single rooms |
| Tunable white | brightness and colour temperature are both adjustable | manual settings or saved scenes |
| Human centric lighting | tunable white + time-of-day schedule + lighting design | home office, children’s rooms, older residents, large living areas |
What do we know about the non-visual effects of light?
Besides rods and cones, the eye contains melanopsin-containing retinal ganglion cells (ipRGCs). They are most sensitive in the bluish range and are involved not in vision but in physiological processes linked to the time of day. Illuminance in lux alone does not describe this effect, so the international standard CIE S 026/E:2018 introduced melanopic EDI (melanopic equivalent daylight illuminance). The standard is a measurement system: it explicitly gives no application recommendations or health limits.
In Germany, DIN/TS 67600:2022-08 (the successor of DIN SPEC 67600) gives supplementary planning criteria for the non-visual effects of light. It is a technical specification: a recommendation, not a mandatory rule.
The most widely cited practical recommendation comes from an international expert group (Brown et al., PLOS Biology, 2022), for healthy adults, measured at eye level in the vertical plane (about 1.2 m when seated):
- During the day: at least 250 lux melanopic EDI.
- In the evening, starting at least 3 hours before bedtime: at most 10 lux melanopic EDI.
- During sleep: the bedroom should be as dark as possible, at most 1 lux melanopic EDI.
Two practical lessons follow. First, it is not only the colour temperature that matters but also how much light reaches the eye: a lamp set to warm white but at full brightness still gives a lot of light in the evening. Second, during the day most light comes from daylight; artificial lighting complements it, it does not replace it. Tunable white lighting therefore helps most in the evening, when warm, subdued light is easy to set.
How we build it: LED strip, DALI DT8, KNX, Casambi
A tunable white system has three parts: the light source (a two-channel LED strip or luminaire), the driver, which controls the two channels separately, and the control, which sets colour temperature and brightness according to the schedule or the buttons.
| Control | How it sets colour temperature | Good for |
|---|---|---|
| DALI DT8 | colour control according to Part 209 of the DALI standard (IEC 62386-209); the driver understands the colour temperature (Tc) command | new build or renovation, many luminaires, with a stand-alone DALI controller |
| KNX + KNX–DALI gateway | on KNX the absolute colour temperature in kelvin (DPT 7.600, 2 bytes) and brightness in percent; the gateway translates to DALI DT8 | KNX house: lighting in one system with shading and heating |
| Casambi | wireless, Bluetooth-based; tunable white scenes and timers are set in the app | finished, occupied house without control cabling |
We have written in detail about DALI DT6 vs DT8, the KNX–DALI gateway and Casambi: DALI lighting control at home: DALI, KNX or Casambi? The key point: a tunable white luminaire needs a DT8 driver and a controller or gateway that handles DT8, otherwise only brightness can be adjusted.
Schedule, daylight simulation: in a KNX house the time program (or a logic module) sends colour temperature and brightness values by time of day; many KNX–DALI gateways and visualisations offer a built-in function for this, which we select based on the manufacturer’s documentation. It is important that manual switching can override the program and that the program takes over again afterwards.
Design criteria: illuminance, glare, colour rendering, flicker
- Illuminance and direction: for non-visual effects, the vertical illuminance reaching the eye matters, not only light on the desk. Light directed onto walls and ceilings (indirect light) helps a lot.
- Home office: for office workplaces, EN 12464-1:2021 specifies 500 lux for writing, reading and typing, glare limitation of UGR ≤ 19 and colour rendering of Ra ≥ 80. Not mandatory at home, but a good benchmark.
- Glare (UGR): deep-recessed downlights, opal diffusers, indirect light; the tunable white light line should not be directly visible at eye level.
- Colour rendering: for homes we recommend light sources with Ra ≥ 90, and we also check colour consistency (MacAdam steps) in the datasheet so that neighbouring luminaires give the same white.
- Flicker: Regulation (EU) 2019/2020 sets Pst LM ≤ 1.0 (visible flicker) and SVM ≤ 0.4 (stroboscopic effect) for mains LED light sources. With LED strips the driver decides; we choose one whose datasheet specifies flicker-free operation even when dimmed low.
- Cabling: because of its two channels, a tunable white LED strip needs a three-core supply cable, and the DALI driver needs the DALI pair alongside the mains conductors. This has to be laid before the drywall goes up: hidden LED strip lighting in drywall.
When is human centric lighting worth it at home?
- Home office: neutral or cooler, ample light for work during the day, warm and subdued light after work from the same luminaire.
- Children’s room: warm, low “evening mode” at the push of a button or on a schedule; in the morning the light increases gradually.
- Older residents: CIE S 026 also takes the effect of age into account, because the lens of the eye transmits less short-wavelength light over the years. Older people generally need more light for the same task; we take this into account in the design.
- Large open-plan living and kitchen area: there are many luminaires, and scenes and dimming need control anyway, so the extra cost of tunable white is smaller.
It is less worthwhile in a pantry, garage, corridor or a room with one or two lights, where a good-quality, warm white dimmable LED is enough.
Our own experience: we installed DALI-controlled tunable white lighting in a family house in the Buda suburbs. The lesson is that the decisions (luminaires, driver type, cabling) have to be made at the design stage; changing them later is expensive.
What does it cost, and what to decide before plastering?
The price depends on the number of luminaires, the drivers (DT8), the control (stand-alone DALI, KNX–DALI gateway or Casambi) and the programming, so we have no price list: individual quote after a site survey or based on the electrical design.
- Which rooms get tunable white? Not every room needs it; the living room, study and children’s room are typical.
- Luminaires and drivers: DT8 driver, Ra ≥ 90, suitable colour temperature range and flicker-free operation according to the datasheet.
- Control: in a KNX house a KNX–DALI gateway, without KNX a stand-alone DALI controller, in an occupied house Casambi.
- Cabling: DALI pair to the drivers, three-core supply cable to the LED strips, drivers in accessible places.
- Schedule: which scene at which time of day, and how it can be overridden manually.
More: LED lighting and lighting control · DALI lighting control · KNX smart home · Smart home
Related articles from our knowledge base
What Ra measures, why R9 matters, what TM-30 adds, and what EN 12464-1 and the EU ecodesign rules require.
Read →DALI-2, D4i, DT6/DT8, KNX–DALI gateways (MDT, Gira, ABB, Lunatone) – what to check, based on datasheets.
Read →Frequently asked questions
What is human centric lighting (HCL)?
Lighting design that takes the non-visual effects of light into account as well as vision: brightness and colour temperature that change with the time of day, with daylight first. Its tools are tunable white luminaires and a control system.
What is tunable white?
White light of adjustable colour temperature from the same luminaire. It contains warm and cool white LEDs, and the driver changes their ratio; the typical range is 2700–6500 K.
Does human centric lighting improve sleep?
We do not promise that. The literature (Brown et al., 2022) recommends less light in the evening and more during the day for healthy adults; HCL makes this easier, but it is not a medical device or a therapy.
What control does a tunable white LED need?
A DALI DT8 driver and a controller or KNX–DALI gateway that handles DT8, or wireless Casambi. On KNX, colour temperature is transmitted in kelvin with datapoint type DPT 7.600.
What is melanopic EDI?
The CIE S 026/E:2018 quantity for the non-visual effect of light: it states in lux how much daylight would have the same effect on the melanopsin receptors. It is measured at eye level in the vertical plane.
What does tunable white lighting cost?
It depends on the number of luminaires, the drivers and the control, so we have no price list. We give an itemised quote after a site survey or based on the electrical design.
Let’s talk about your project.
Tell us what you are planning and we will get back to you within a few days.
Get in touch