KNOWLEDGE BASE · LIGHTING

LED profiles and hidden LED strip lighting in drywall: what to decide before the boards go up

Hidden LED lighting in plasterboard looks good and lasts when the key decisions are made before the boards go up: where the line of light runs (cove, plaster-in LED profile or cornice), which strip goes in, where the driver sits, and how it will be switched and dimmed. Anything missed at that stage can only be added later by opening the wall or ceiling. This article goes through the decisions and ends with a checklist.

In short

  • Which detail? A plasterboard cove gives soft, indirect light; a plaster-in LED profile a crisp line of light; a cornice can be added later without opening anything.
  • Which strip? In a home usually a 24 V strip with high colour rendering (CRI above 90); where the strip is seen directly, a COB strip, because it shows no dots.
  • Where is the driver? Somewhere accessible and ventilated, not sealed behind the plasterboard. It is sized with headroom.
  • What must be run in first? The 230 V supply to the driver location, the low-voltage cable to every feed point of the strip and, if needed, the control cable (e.g. DALI).

Author: Norbert Madarász, Managing Director and Partner · Updated: 8 November 2026

What kinds of hidden lighting can be built in drywall?

There are three common solutions, each good in the right place. They differ in light, space needed and when you must decide.

SolutionLightAdvantageWatch out for
Plasterboard cove (light trough)diffuse light washing the ceiling or wallthe strip is hidden, the light is even, the strip is reachable from aboveneeds space at the ceiling edge; the line is set when the suspended ceiling is designed
Plaster-in (trimless) LED profilea sharp, narrow line of light in the wall or ceilingflush, clean appearancethe profile goes in together with the boards; the skim must be careful, or the light picks out every surface flaw
Cornice (polystyrene or polyurethane)diffuse light, similar to a covecan be glued on later, no demolitiona cornice does not conduct heat, so the strip still belongs in an aluminium profile, or should be a lower-power one

The aluminium wings of plaster-in profiles are fixed to the plasterboard, then skimmed over and painted; some manufacturers (e.g. Klus Design) supply a protective insert for installation and skimming so the diffuser slot does not fill up. For suspended-ceiling lighting the cove or profile line has to be set out when the framing is designed, just like the positions of recessed downlights.

Do you need a 12 V or a 24 V LED strip?

In a home, where the strip is longer than a few metres, we usually recommend a 24 V LED strip. At the same power it carries half the current, so the voltage drop is lower and a longer section runs evenly from one feed.

Exactly how long depends on the product, not on the voltage alone. Some manufacturer examples:

  • Signlite’s general figure for one feed is 5 m at 12 V and 10 m at 24 V.
  • For one ENTTEC 24 V, 14.6 W/m SMD strip the maximum is 10 m from one feed and 13 m fed from both ends.
  • For a LEDVANCE 24 V COB strip (1000 lm/m) the maximum is 5 m with the driver right next to it; with a 10 m, 0.5 mm² supply cable it falls to 3.4 m.

The last example is the point: the cable between driver and strip counts too. A long strip is therefore split into sections, each with its own feed, or fed from both ends. That means the cables have to be in place before the plasterboard goes up. If a strip is longer than allowed, its far end will be dimmer and its colour may shift.

COB or SMD strip? Which colour temperature and CRI?

  • SMD strip: separate LEDs in a row. Where the strip or its reflection is seen directly, the points can show as dots, especially on glossy surfaces.
  • COB strip: densely placed chips under a continuous phosphor layer give an unbroken line of light (in LEDVANCE’s words, “all line, no dots”). For plaster-in profiles and shallow coves it is the safer choice.
  • Colour temperature: usually 2700–3000 K (warm white) in living spaces; 3000–4000 K also works over a kitchen worktop. If you cannot decide, a tunable white strip lets you adjust it later, but it needs more conductors.
  • Colour rendering (CRI): we recommend at least CRI 90 in a home; good manufacturers state it on the datasheet. Check R9 (saturated red) too: it is not part of Ra and can be weak on an LED strip even with a good Ra – details: CRI, R9 and TM-30.

What does the LED profile and diffuser do?

The aluminium LED profile carries the heat away, and the diffuser evens out the light and protects the strip. Heat matters: manufacturers state strip lifetime at a defined temperature (for LEDVANCE’s COB strip, 50,000 hours at a measuring point of no more than 65 °C), and ENTTEC explicitly requires mounting on a thermally conductive surface. We therefore never stick a strip directly onto plasterboard or a cornice.

Whether a strip in a given profile and diffuser shows dots depends on LED density, diffuser material and the distance between strip and diffuser; there is no general figure, so we pair them following the profile and strip manufacturers’ recommendations.

Which LED profile for drywall: plaster-in, recessed or surface-mounted?

An LED profile is the aluminium channel that holds the strip, not a lighting track. For drywall there are four basic types; the choice depends on how invisible the profile should be and when the position of the light line was decided.

ProfileWhat it looks likeWhen it goes inWhat to watch
Plaster-in (trimless)only the light line is visible, no edgetogether with the boards: the flange is screwed to the board and plastered overfollow the manufacturer instructions for the board thickness and profile type
Recessed (U-profile with trim)the narrow edge of the profile is visibleinto an opening cut in the finished or unfinished surfacethe opening size is given by the profile; plan the cable route in advance
Corner profileat the ceiling–wall junction, lighting at an anglewith the boards or later, depending on the typethe corner must be straight, or the light line will wave too
Surface-mounted profilea visible profile on the surfacelater as well, without openingit is visible, so a cove or a moulding looks better if there is room

Cover (diffuser): an opal cover gives a more even, dot-free line of light; a clear cover lets more light through, but the LED dots may show. Whether a given strip shows dots depends on the profile and cover data from the manufacturer, so we choose profile, cover and strip together. The inner channel of the profile must match the strip width; the profile datasheet states it.

If you need movable spots rather than a fixed light line, that is not an LED profile but a magnetic track system: 48 V magnetic track lighting.

How is an LED profile installed in drywall?

The sequence for a plaster-in profile, based on the Klus Design installation instructions for the PDS-UST profile (other manufacturers are similar, but the instructions of the actual profile always take precedence):

  • Cable exit: a hole is drilled in the profile for the feed cable, with an end cap and a gland. The cable position is planned together with the driver location.
  • Fixing: the flange of the profile is screwed to the board with drywall screws; Klus gives a maximum hole spacing of 400 mm.
  • Protective insert: an insert goes into the profile to keep the inside clean while plastering.
  • Plaster, sand, paint: the flange is plastered over, sanded once dry, then painted.
  • Removing the insert: the paint and plaster layer is cut along the profile edge and the insert is carefully removed.
  • Strip and cover: the LED strip goes in only after painting, followed by the end caps and the cover.

So the strip goes into the painted profile after the finishing work, and the cover is removable: the strip can be replaced later as long as the cable and the driver stay accessible. That is why the driver belongs behind an access panel (see below), and why we plan the cable exit so it reaches the end of the strip.

Where should the LED driver go?

The driver (power supply) belongs somewhere accessible and ventilated, not sealed behind the plasterboard: drivers can fail and need replacing, and heat shortens their life, so in an enclosed space their output has to be derated. The standard (HD 60364-5-52, 526.3) also requires connections to be accessible for inspection, testing and maintenance, with a few exceptions (e.g. maintenance-free terminals).

  • Good places: an access hatch in the plasterboard, the top of a wardrobe or wall cabinet with ventilation, a plant room, or a DIN-rail driver in a lighting distribution board.
  • Bad places: a closed ceiling without an access hatch, buried under insulation, a closed kitchen cabinet with no airflow.
  • The cost of distance: the further the driver is from the strip, the heavier the low-voltage cable needs to be, or the shorter the strip section (see the LEDVANCE example above).

What size of driver do you need?

Strip power (W/m) times length gives the load, and the driver is chosen with headroom. A common trade rule of thumb is to load a driver to no more than about 80% (Flexfire LEDs and Signlite both suggest about 20% reserve; for some high-efficiency drivers the manufacturer allows 90%). This is not a standard value: derating for warm locations is always given on the driver’s datasheet.

Which driver to choose? Mean Well, OSRAM and LEDVANCE

  • A constant-voltage (CV) driver is needed for LED strip, at the same voltage as the strip (12 or 24 V). Constant-current (CC) drivers are for spots and panels, not for strip.
  • A design that suits the location: a DIN-rail driver in the lighting distribution board (at Mean Well, for example, the HDR or NDR series), and an encapsulated, water-protected driver for damp or outdoor locations (for example Mean Well’s LPV, ELG or HLG series). The exact protection (IP65 or IP67) is given by the suffix of the type code and the datasheet.
  • Dimming: driver and control must match: a DALI or 1–10 V dimmable driver, or a fixed driver followed by a PWM dimmer. More below, and: LED dimmer switches.
  • OSRAM and LEDVANCE: OSRAM-branded lamps are made by LEDVANCE under licence (since 2016, according to ams OSRAM and LEDVANCE). LEDVANCE strip datasheets state how long a section can be fed from one point and how much the supply cable shortens it (see the example above); we follow that figure, not the rule of thumb.

Kitchen worktop lighting with LED strip

The under-cabinet strip goes into a profile, the driver on top of the cabinets or into a ventilated compartment, and the switch above the worktop where it is easy to reach. This has to be agreed with the kitchen maker, because the cable also has to pass through the carcass.

How is an LED strip made dimmable?

A dimmable LED strip needs a dimmable driver or a separate LED controller; the strip itself is almost always dimmable. The choice decides which cables go into the wall:

  • From a wall dimmer (phase cut): only with a driver the manufacturer specifies for phase-cut dimming. More: LED dimmer switches.
  • With a DALI driver: a two-wire control cable runs alongside the 230 V, so the lighting can also be controlled from KNX or scenes. More: DALI lighting control.
  • Wireless (e.g. Casambi): the controller sits between driver and strip, so it also needs an accessible place.
  • Tunable white or colour strip: a single-colour strip needs 2 conductors, tunable white 3, RGB 4, RGBW 5 from driver to strip. Decide before the boards go up.

What should you decide before the plasterboard goes up?

This table is the pre-installation checklist. If every row has an answer, the boards can go up.

QuestionWhat to decideWhy now
Where does the light run?cove, plaster-in profile or cornice; exact line and lengththe profile goes in with the boards, the cove is part of the framing
Which strip?voltage (12/24 V), W/m, COB or SMD, colour temperature, CRI, single colour or tunablethis sets the number of feed points and conductors
How many feeds?section length per the datasheet, fed from one or both endsevery feed point needs a cable behind the wall or ceiling
Where is the driver?accessible, ventilated place; position and size of the access hatchonce the plasterboard is closed you cannot get behind it
What size of driver?total load with headroom, type chosen by dimming methoddriver size sets the space and ventilation needed
How is it switched and dimmed?wall dimmer, DALI, KNX, Casambi; switch positionscontrol cables and switch boxes go into the wall
Which cables?230 V to the driver; low voltage to the strip with adequate cross-section; control cableafter boarding, only by opening up or with visible trunking

Who should design and install it?

Sticking a low-voltage strip in place is simple; the rest of the system is not. The 230 V supply, the driver location and the sizing are electrician’s work. Before boarding we survey the site or the drawings, set out the feed points and the driver location and run the cables; after boarding we install the profile, the strip and the controls. We have already installed DALI, Casambi and tunable white lighting in family homes.

We quote on the basis of a site survey or the design drawings. More: LED lighting and lighting control · Electrical installation · Electrical design

Frequently asked questions

Which LED strip is right for hidden lighting in drywall?

In a home usually a 24 V strip with CRI 90 or more, in an aluminium profile. Where the line of light is seen directly, for example in a plaster-in profile, a COB strip, because it shows no dots.

How long can an LED strip be from one feed?

It depends on the product. Manufacturer examples: typically about 5 m at 12 V and 5–10 m at 24 V; for one LEDVANCE 24 V COB strip 5 m, which falls to 3.4 m with a long supply cable. Longer strips are split into sections or fed from both ends.

Where should the LED driver go?

Somewhere accessible and ventilated: behind an access hatch, on top of a cabinet, in a plant room or in the lighting distribution board. Not behind closed plasterboard or under insulation, because it must be replaceable and heat shortens its life.

What size of LED driver do I need?

Strip W/m times length, plus headroom: a common rule of thumb is to load the driver to no more than about 80%. In warm or enclosed places derate further according to the driver’s datasheet.

Does an LED strip need a profile?

Yes, we recommend one. The aluminium profile carries the heat away, the diffuser evens out the light and protects the strip. Manufacturers state lifetime at a defined temperature and require mounting on a thermally conductive surface.

Can an LED strip be dimmed from a wall dimmer?

Only with a driver the manufacturer specifies for phase-cut dimming. Alternatives are a DALI driver or a wireless controller (e.g. Casambi); their cabling has to be decided before the plasterboard goes up.

What is the difference between a plaster-in and a recessed LED profile?

A plaster-in profile is screwed to the plasterboard by its flange and plastered over, so only the light line shows, with no edge. A recessed (trimmed) profile sits in an opening cut into the surface, and its narrow edge is visible. The plaster-in type must go in with the boards; the recessed type can also be added later.

When should the LED profile be installed: before or after the plasterboard?

A plaster-in profile goes in with the boards, before plastering: its flange is screwed to the board and plastered over. By then the cable exit and the driver location must be decided. The LED strip goes into the profile only after painting.

Corner profile or a hidden cove?

A cove gives soft, indirect light bounced off the ceiling and hides the strip, but needs room at the ceiling edge. A corner profile needs less space and lights at an angle from the wall–ceiling junction, but its light line is visible.

Can the strip in the profile be replaced later?

Yes, if it is built properly: the strip goes into the profile after painting, and the cover is removable. The cable and the driver must stay accessible, which is why we put the driver behind an access panel.

Let’s talk about your project.

Tell us what you are planning and we will get back to you within a few days.

Get in touch

Cookie settings

Choose what you consent to. We remember your choice for 6 months; change it any time via “Cookie settings” in the footer.

Privacy notice